MAX HPPE Steel Composite PU Palm Coated Cut Resistant Gloves - TDM Cut Level E

Who is this for

HPPE steel composite PU palm coated cut resistant gloves at TDM Cut Level E are used primarily by glaziers, sheet metal fabricators, metalworkers, construction operatives, and engineers working with materials where a confirmed high-level cut rating under EN388:2016 is required alongside dexterity and dry grip. The TDM Level E rating at 22 Newtons makes these gloves appropriate for tasks involving glass sheets, sharp sheet metal edges, blade-adjacent work, and waste management sorting where cut hazard is frequent and a lower TDM level has been identified as insufficient by the task risk assessment. The five-material composite liner delivers the TDM Level E protection whilst the spandex component maintains the stretch and close fit needed for precision handling tasks throughout a full shift. Site managers, safety officers, and procurement teams sourcing a single high-cut-protection grip glove for glazing, fabrication, and engineering environments will find these gloves meet EN388:2016+A1:2018 requirements as confirmed by CTC Notified Body No. 0075. The colour-coded cuff system allows rapid correct-size issue across large workforces.

Typical applications

Glass sheet handling and glazing installation on construction and refurbishment sites where the sharp edges of cut glass present a TDM Level E cut risk throughout the handling and installation process.

Sheet metal fabrication, handling, and installation in engineering and construction environments where sharp cut edges, burrs, and thin metal sections present a persistent high-level cut hazard during component handling and assembly.

Blade-adjacent work in manufacturing and engineering environments where operatives work in close proximity to cutting equipment and the task risk assessment identifies a cut hazard above TDM Level C or D.

Waste management and recycling sorting where mixed waste streams containing glass, metal, and sharp construction debris present a frequent and unpredictable cut hazard requiring the highest practical everyday cut protection.

Construction demolition and strip-out tasks involving broken glass, sharp metal fixings, and cut construction materials where the cut hazard profile exceeds what TDM Level C provides.

Metal component and fabricated section handling in manufacturing, automotive, and engineering assembly environments where sharp edges, press-formed sections, and stamped components present a sustained cut risk throughout the production shift.

How to use

Step 1: Select the correct size using the colour-coded cuffs. At 13 gauge, correct sizing is essential for maintaining the close fit that preserves both cut protection and tactile sensitivity.

Step 2: Inspect the PU coating and composite liner before each use. Check the palm and fingertip area for visible wear, thinning, or damage to the coating or liner. Do not use a glove where the liner is worn through or the PU coating is cracked, as cut protection is compromised once the liner is damaged.

Step 3: Pull the glove fully over the hand, ensuring all fingers are completely seated with the PU coating covering the full palm and front of fingers. Check that no liner bunching is visible at the fingertips.

Step 4: Seat the elasticated knitted cuff flat against the wrist before beginning work.

Step 5: After use, wipe with a damp cloth to remove debris and light contamination. Do not launder or dry-clean: performance levels are rated for new condition only and cannot be guaranteed after washing.

Step 6: Air dry fully before storing. Store away from direct sunlight, heat sources, and ozone.

Step 7: Replace when the PU coating shows visible thinning or cracking, when the composite liner shows wear, or when cut protection can no longer be confirmed by visual inspection.

Common mistakes

Assuming cut-resistant means cut-proof: TDM Cut Level E means the glove resisted a straight blade at 22 Newtons before penetration in a controlled laboratory test. It does not make the glove impenetrable. A powered cutting tool such as a grinder, saw, or angle grinder will cut through any glove. Never use cut-resistant gloves as protection against powered cutting equipment.

Specifying TDM Level E where the risk assessment requires Level F: TDM Level E is the second-highest protection level. For tasks where the risk assessment identifies the highest possible cut hazard, TDM Level F (30N) must be specified. Confirm the required TDM level from the task risk assessment before specifying.

Confusing EN388 puncture resistance with needle-stick protection: Level 3 puncture resistance (100N) reflects resistance to a blunt probe under the EN388 test. It does not confer needle-stick protection against hypodermic needles or fine sharp points.

Using on wet or contaminated surfaces: PU coating performs in dry conditions. On oily, greasy, or wet surfaces, PU loses traction. For mixed-hazard environments where TDM Level E cut protection and grip in wet conditions are simultaneously required, a foam nitrile or sandy nitrile cut-resistant alternative should be evaluated.

Washing or dry cleaning: Performance levels are rated for new condition only. Wipe with a damp cloth and air dry only.

Safety

These gloves are certified to EN388:2016+A1:2018 (4X43E) and EN ISO 21420:2020, CE marked Category II, with type examination by CTC Notified Body No. 0075. TDM Cut Level E protects against straight-blade cut hazards at 22 Newtons under ISO 13997 and is appropriate for glass handling, sheet metal fabrication, and high-cut-risk construction and engineering tasks. These gloves do not protect against powered cutting tools, heat, flame, chemical immersion, or needle-stick hazards. Do not use near moving machinery due to the entanglement hazard noted in the user instructions. A task-specific risk assessment under the Personal Protective Equipment at Work Regulations 1992 must confirm the TDM level is sufficient for the specific cut hazard before specifying these gloves.

Maintenance

Wipe with a damp cloth after use to remove debris and contamination. Air dry fully at room temperature before storing. Store in dry conditions away from direct sunlight, heat sources, and ozone. Inspect the PU coating and composite liner before every use. Replace when the coating or liner shows visible damage, thinning, or wear, or when cut protection can no longer be confirmed by inspection.