MAX Heavy Duty Polyester Latex Grip Gloves - Construction and Bricklaying

MAX Heavy Duty Polyester Latex Grip Gloves

The MAX Heavy Duty Polyester Latex Grip Gloves are built for the repetitive, abrasive demands of bricklaying, scaffolding, and heavy site handling. The crinkle latex palm coating provides a textured, high-traction surface that maintains grip on rough and uneven materials in both wet and dry conditions. A durable polyester knitted liner keeps the glove close-fitting and shape-retaining across long shifts, where cheaper polycotton alternatives lose structure and reduce grip sensitivity.

Why Choose the MAX Heavy Duty Polyester Latex Grip Gloves

• Crinkle latex palm coating: The textured latex surface creates multiple grip contact points on brick, block, timber, and scaffold components. Unlike flat or smooth latex coatings, the crinkle construction channels away moisture and maintains traction on damp surfaces throughout a shift.

• Polyester liner construction: Polyester holds its shape and resists stretching under repeated heavy use. Polycotton liners, common in budget alternatives, lose structure with wear and reduce the close fit needed for reliable grip sensitivity.

• EN388:2016+A1:2018 rated 2243X: Tear resistance level 4 and puncture resistance level 3 make this one of the strongest-rated general construction grip gloves in this category. Budget latex grip gloves typically rate at 2121X, which is significantly lower across both measures.

• Breathable open-knit back: The uncoated back of hand allows heat and moisture to escape, reducing hand fatigue and sweat build-up across sustained site shifts without compromising palm protection.

• Elasticated knitted cuff: The cuff seats firmly at the wrist and prevents grit, dust, and concrete debris from entering the glove during ground-level handling and block laying.

• Full size range to XXL: Available in M, L, XL, and XXL (8 to 11), covering the full range of hand sizes across a site team without the need to source multiple glove types.

• Plastic-free, zero-waste packaging: Part of the CMT ThinkGreen range, supporting sites with ESG and Scope 3 reporting requirements.

What's Included

• 12 pairs of MAX Heavy Duty Polyester Latex Grip Gloves in your chosen size (M, L, XL, or XXL), supplied in plastic-free packaging.

 Specifications

Compatibility

Who Is This For?

The MAX Heavy Duty Polyester Latex Grip Gloves are the everyday site glove for bricklayers, scaffolders, groundworkers, and general construction operatives handling rough, abrasive materials across UK construction sites. They are suited to any trade where grip, durability, and hand comfort across a full shift matter more than waterproofing or cut resistance.

Typical Applications

• Laying bricks and blocks where consistent grip on rough masonry reduces drops and repetitive strain

• Moving and positioning scaffold tubes, boards, and fittings where secure handling reduces pinch risk

• General site material handling including timber, aggregate bags, and kerb stones

• Strip-out and demolition support tasks involving rough or uneven surfaces

• Maintenance and repair work requiring a durable grip glove across varied conditions

• Site setup and logistics including unloading and stacking materials from delivery vehicles

• Groundwork tasks in dry or lightly damp conditions where a waterproof glove is not required

How to Use

1. Select the correct size: M (8), L (9), XL (10), or XXL (11). A close fit maximises grip sensitivity and reduces hand fatigue.

2. Pull the glove fully over the hand and ensure the elasticated cuff seats firmly at the wrist.

3. Check the cuff is flat and free of folds before starting work to prevent debris ingress.

4. Inspect the latex palm before each use. Replace when the coating shows visible cracking, peeling, or significant thinning at the fingertips or palm.

5. Do not use these gloves for tasks requiring waterproof protection, cut resistance above EN388 level 2, or chemical handling.

Safety

Certified to EN388:2016+A1:2018 (2243X) for mechanical risk protection. Not suitable for sharp blade tasks, chemical contact, heat, or flame. The crinkle latex palm provides grip in light damp conditions but these gloves are not waterproof. Operatives with a latex allergy must not use them and should be issued a nitrile alternative.

Maintenance

Rinse in clean water after use if contaminated with concrete or mortar residue. Air dry away from direct heat. Store away from solvents and direct sunlight. Inspect the palm coating before each shift and replace when wear is visible.

Frequently Asked Questions

Q: What does the EN388:2016+A1:2018 2243X rating mean for this glove?

 A: EN388 is the UK and European standard for mechanical risk protection gloves. The 2243X rating breaks down as: abrasion level 2, blade cut level 2, tear level 4, puncture level 3, TDM cut not tested. Tear level 4 and puncture level 3 are significantly higher than the 2121X rating found on most budget latex grip gloves, making this a more durable choice for heavy construction handling tasks.

Q: What is the difference between this glove and the standard Latex Grip Gloves? A: The Heavy Duty Polyester Latex Grip Gloves use a polyester liner rather than polycotton, which holds its shape better under sustained heavy use. The EN388 rating of 2243X is also significantly stronger than the 2121X of the standard version, particularly in tear and puncture resistance. These are the right choice for bricklaying, scaffolding, and heavy site work. The standard version suits lighter general handling tasks.

Q: Are these gloves waterproof? A: No. The crinkle latex palm provides grip in light damp conditions but the back of the hand is open-knit and uncoated. For tasks involving sustained water contact or wet concrete, the MAX Foam Latex Waterproof Gloves provide full waterproof coverage.

Q: Are they suitable for bricklaying specifically? A: Yes. The crinkle latex coating grips the rough face of bricks and blocks reliably, and the tear level 4 rating reflects the durability needed for sustained contact with abrasive masonry surfaces across a full working day.

Q: Can operatives with a latex allergy use these? A: No. These gloves contain natural latex. Operatives with a confirmed or suspected latex allergy must not use them. A nitrile-coated alternative should be issued instead.

Q: Why are they supplied in packs of 12? A: The pack of 12 pairs is designed for site procurement rather than individual purchase. It covers a full small team or provides a working supply for a single operative across a project without repeated reordering.

Q: Are these part of the CMT ThinkGreen range? A: Yes. Supplied in plastic-free, zero-waste packaging as part of CMT ThinkGreen, supporting sites reporting against Scope 3 emissions targets or net-zero commitments.

Q: How do I order and what are the delivery options? A: Order at cmt.co.uk. Next working day delivery for online orders placed by 7pm. VIP dedicated delivery is available UK-wide, dispatched within 30 minutes on a dedicated vehicle. Trade accounts and bulk pricing are managed through the EDGE procurement portal with agreed pricing, role-based spending controls, and live delivery tracking.