Kratos Work Restraint Kit - 1.5m Kernmantle Rope Lanyard and Steel Screw Karabiners

Kratos Work Restraint Kit

A work restraint system does one specific job: it prevents the operative from physically reaching the edge or fall hazard in the first place. This kit is not a fall arrest system and carries no energy absorber, because none is required when the lanyard length is correctly set to keep the operative away from the hazard zone. It is the right choice for scissor lift platforms, roof hatch access, and any task where the method statement specifies restraint as the control measure. Everything needed arrives certified and ready to use in a jute carry bag.

Why Choose the Work Restraint Kit

• Restraint, not arrest: The 1.5m kernmantle lanyard is set to a length that physically prevents the operative from reaching the fall edge. This is a fundamentally different control measure from fall arrest and must only be used where the risk assessment confirms a fall cannot occur if the system is used correctly.

• Two steel screw karabiners: Both connectors are EN362:2004 Class B rated. Two karabiners allow connection at both the anchor point and the harness attachment, eliminating the need to source connectors separately.

• Kernmantle rope construction: Durable and abrasion-resistant, suited to the range of surfaces and environments where restraint systems are typically deployed, including MEWP platforms and flat roof access points.

• Full body harness included: Correctly distributes any incidental loading across the body. A work positioning belt alone is not sufficient where a full body harness is specified in the method statement.

• Compact and lightweight: Without the energy absorber, rope anchorage, or guided arrester of a fall arrest kit, this is a minimal system suited to tasks where simplicity and speed of deployment matter.

• Jute carry bag: Keeps all components together, clean, and protected between uses.

• Certified matched system: All components carry CE marking and are certified compatible, satisfying EN365 requirements for a complete, compliant system.

A fall protection system must include at least three components:

1: The gripping system of the body: harness, belt.

2: The fall arrest system: fall arrest on anchor line, retractable fall arrest, energy absorbing lanyard.

3: The anchoring system: anchor lanyard lifeline, tripod...

The user security can be guaranteed only if:

• These three components have the CE marking ;
• These three components are compatible together ;
• The user has been trained in the usage of these three components.

! A fall arrest system can be complete only if a rescue plan has been established in advance in order to cope with any emergency that may arise during work.

What's Included

• Full body harness

• 1.5m kernmantle rope lanyard

• Two steel screw karabiners

• Jute carry bag

 Specifications

Compatibility

Who Is This For?

This kit is for trained operatives working in environments where a risk assessment has confirmed that restraint is the appropriate control measure and a fall cannot occur if the system is correctly set up and used. Typical users include maintenance technicians on MEWP platforms, facilities managers carrying out flat roof inspections, and operatives accessing roof hatches or plant areas where the lanyard length prevents them from reaching the unguarded edge.

Typical Applications

• Scissor lift and MEWP platform work where the operative must be tethered to the platform anchor point

• Flat roof inspection and maintenance where the lanyard length keeps the operative within the safe zone

• Roof hatch access where the operative works close to the opening but must not reach the roof edge

• Plant room and rooftop equipment maintenance with a fixed anchor and defined exclusion zone

• Any task where the RAMS document specifies work restraint as the primary control measure

How to Use

1. Inspect all components before use. Check the lanyard for cuts, abrasion, or contamination. Check both karabiners open, close, and lock correctly. Do not use any component that fails inspection.

2. Confirm the anchor point is rated for the intended use and positioned so that the 1.5m lanyard, when fully extended, does not allow the operative to reach the fall hazard. This calculation must be done before donning the kit.

3. Don the harness and adjust all straps: chest first, then thighs, then shoulders. No more than two finger widths of slack at any strap.

4. Connect one karabiner to the harness attachment point and tighten the screw gate fully. Connect the second karabiner to the rated anchor point and tighten the screw gate fully.

5. Confirm the lanyard length does not allow you to reach the fall edge before beginning work. If it does, the anchor position must be adjusted or a different control measure used.

6. Do not extend, knot, or modify the lanyard to gain additional reach. Doing so defeats the restraint system entirely.

7. On completion, unclip from the anchor first. Stow all components in the jute bag.

Safety

This is a work restraint system, not a fall arrest system. It must only be used where the risk assessment confirms a fall cannot occur when the system is correctly set up. If there is any possibility of a fall, a fall arrest system must be used instead. The anchor point must be positioned so the fully extended lanyard prevents the operative from reaching the hazard: if this cannot be achieved, this kit is not the right solution for the task. Wear a hard hat to EN397 and safety footwear to EN ISO 20345. Do not use this kit for confined space entry, rescue, or any application outside its certified scope.

Maintenance

After each use, wipe down the harness, lanyard, and both karabiners. Remove dirt, moisture, and contamination before returning to the jute bag. Dry all components naturally away from direct heat. Inspect the kernmantle rope along its full length at each pre-use check: any cut, stiffness, or abrasion means immediate withdrawal. Formally inspect all components by a competent person at intervals not exceeding 12 months, with written records kept per PUWER. Check the manufacturer's label for the applicable service life and retire the equipment accordingly.

Frequently Asked Questions

Q: What is the difference between a work restraint kit and a fall arrest kit?

 A: A work restraint system prevents the operative from reaching the fall hazard by limiting how far they can move. A fall arrest system arrests a fall after it has occurred. Restraint is the appropriate control only when the risk assessment confirms a fall cannot happen if the system is correctly used: the lanyard must be short enough that the operative physically cannot reach the unguarded edge. If there is any doubt, fall arrest is the correct choice.

Q: What do EN361:2002, EN354:2002, and EN362:2004 Class B mean for this kit?

 A: EN361:2002 covers the full body harness, specifying how forces must be distributed across the body. EN354:2002 covers the lanyard. EN362:2004 Class B covers the steel screw karabiners, confirming their rated strength and gate locking performance. All three are required under the Personal Protective Equipment at Work Regulations 1992 for restraint PPE used on UK sites. CE marking to these standards is the legal declaration of compliance.

Q: Why does this kit not include an energy absorber?

 A: A work restraint system is designed to prevent a fall from occurring, not to arrest one. Because no fall should occur when the system is correctly set up and used, an energy absorber is neither required nor appropriate. Including one would not make the system safer: it would simply add weight and complexity. If there is a risk of a fall, this kit is not the right product and a fall arrest kit must be specified instead.

Q: Can this kit be used on a scissor lift or MEWP?

 A: Yes. Scissor lifts and MEWPs are one of the most common applications for work restraint systems. The operative connects to the platform anchor point via the lanyard, preventing them from being thrown clear of the platform in the event of a tip or sudden movement. Confirm the platform has a rated anchor point before use and that the lanyard length is appropriate for the platform size.

Q: Can I use this kit for roofing work?

 A: Only if the risk assessment confirms the lanyard length prevents you from reaching the roof edge at any point during the task. If there is any possibility of reaching an unguarded edge, a fall arrest kit must be used instead. Restraint is appropriate for tasks such as roof hatch access or plant maintenance in a defined zone away from the edge, not for general roofing operations.

Q: How often must this kit be formally inspected?

A: Pre-use inspection by the wearer is required before every session. Formal inspection by a competent person is required at intervals not exceeding 12 months, with written records kept per PUWER. Check the manufacturer's label for the specific service life applicable to this kit.

Q: Where can I order this kit and how quickly can I get it to site?

 A: CMT Group supplies this kit from stock with next working day delivery on orders placed by 7pm online or 5pm by phone. Same-day delivery is available: call the team to confirm stock and arrange despatch. CMT operates its own fleet of over 100 FORS Silver accredited vehicles covering 90% of the UK, with live tracking and SMS notification 15 minutes before arrival. For contractors managing multiple projects, the EDGE portal provides agreed contract pricing, spending controls, and full delivery visibility in one place.