Makita DUT130Z 18V LXT brushless cordless paddle mixer for construction and decorating professionals, sold as body only without battery or charger.
- 18V LXT brushless motor, maintenance-free with extended service life
- Two speed ranges: 0-350 rpm (low) and 0-1,300 rpm (high)
- XPT technology for improved dust and water resistance on site
- Soft start reduces start-up impact on motor and material
- 165mm maximum mixing blade diameter, M14 spindle thread
- Body only, requires Makita 18V LXT battery and charger sold separately
- Compatible with Makita BL1815N to BL1860B battery range
Makita DUT130Z 18V LXT Brushless Cordless Paddle Mixer - Body Only
Makita DUT130Z 18V LXT brushless cordless paddle mixer for construction and decorating professionals, sold as body only without battery or charger.
- 18V LXT brushless motor, maintenance-free with extended service life
- Two speed ranges: 0-350 rpm (low) and 0-1,300 rpm (high)
- XPT technology for improved dust and water resistance on site
- Soft start reduces start-up impact on motor and material
- 165mm maximum mixing blade diameter, M14 spindle thread
- Body only, requires Makita 18V LXT battery and charger sold separately
- Compatible with Makita BL1815N to BL1860B battery range
- Buy 3 for £366.54 £305.45 each and save 4%
- Buy 6 for £346.80 £289.00 each and save 9%
| BULK DISCOUNT | 3 | 6 |
|---|---|---|
| Price | £305.45 £366.54 | £289.00 £346.80 |
Order 1x to earn 319 FASTPoints
Order to earn 319 FASTPoints
Log in to access trade discountsMakita DUT130Z 18V LXT Brushless Cordless Paddle Mixer
Cordless paddle mixers remove the cable constraint from site mixing tasks without sacrificing the power and control needed for render, plaster, mortar, and paint. The Makita DUT130Z uses an 18V LXT brushless motor across two variable speed ranges, with XPT dust and water resistance and a soft start system built in. This listing is body only, battery and charger are not included and must be purchased separately from the Makita 18V LXT range.
Why a brushless motor makes a difference on heavy mixing tasks
A brushed motor relies on carbon brushes making physical contact with the rotor to pass current. Those brushes generate friction, produce heat under sustained load, and wear down over time. For a tool used intensively on plastering, rendering, or decorating tasks across a full working day, that wear translates directly to reduced performance and eventual motor failure. The brushless motor on the DUT130Z has no contact brushes. It runs cooler under sustained load, delivers more consistent torque throughout the mixing session, and has a significantly longer service life without maintenance.
Key Features
-
18V LXT brushless motor: Maintenance-free design with extended service life. Compatible with the full Makita 18V LXT battery platform, buyers already using LXT tools can share batteries across the fleet.
-
Two variable speed ranges: Low speed (0-350 min⁻¹) for high-viscosity materials including mortar and thick adhesives. High speed (0-1,300 min⁻¹) for paints, thin renders, and lighter materials. Speed is selected via the speed change knob when the tool is fully stationary.
-
Variable speed trigger: Speed within each range adjusts progressively with trigger pressure, giving precise control over the mixing action.
-
XPT eXtreme Protection Technology: Engineered for improved dust and water resistance for operation in harsh site conditions.
-
Soft start: Reduces the start-up impact on both the motor and the material being mixed, preventing splashing and protecting the tool.
-
Battery protection system: Automatic shut-off on overload, overheating, and over-discharge to protect both tool and battery during sustained use.
-
Front cover and side handle: Both included. The front cover reduces the risk of spattered material reaching the battery compartment. The side handle can be fitted to either side of the tool.
-
M14 spindle thread: Compatible with standard M14 mixing paddles including the CMT MP115M14 Heavy Duty Mixing Paddle.
Who is this for
Trades and roles:
-
Plasterers and renderers
-
Tilers and flooring operatives
-
Decorators and painters
-
Groundworkers and concreters
-
Site operatives
Industries:
-
Construction
-
Civil engineering
-
Decorating and finishing
-
Tiling and floor laying
-
Facilities management
Specifications
| Specification | Detail |
| Product Name | Makita DUT130Z 18V LXT Brushless Cordless Paddle Mixer - Body Only |
| SKU | MAK-DUT130Z-BODY |
| Brand | Makita |
| Model | DUT130Z |
| Voltage | 18V DC |
| Battery Platform | Makita LXT |
| Motor | Brushless |
| No-Load Speed (High) | 0 to 1,300 min⁻¹ |
| No-Load Speed (Low) | 0 to 350 min⁻¹ |
| Max Mixing Blade Diameter | 165mm |
| Spindle Thread | 1/2" (M14) |
| XPT Protection | Yes — eXtreme Protection Technology, engineered for improved dust and water resistance |
| Soft Start | Yes |
| Variable Speed Trigger | Yes |
| Speed Settings | 2 (selectable via speed change knob) |
| Battery Protection | Overload, overheat, over-discharge auto shut-off |
| Sound Pressure Level | 77 dB(A), uncertainty K = 3 dB(A). May exceed 80 dB(A) during use. |
| Vibration (3 axes) | ≤ 2.5 m/s², uncertainty K = 1.5 m/s² |
| Dimensions (L x W x H) | 320 x 89 x 231mm |
| Weight (body only) | 1.9 kg |
| Weight (with battery) | 2.5 to 2.8 kg |
| Compatible Batteries | BL1815N, BL1820B, BL1830B, BL1840B, BL1850B, BL1860B |
| Battery Included | No — body only |
| Charger Included | No — body only |
Compatibility
| Application or condition | Status |
| Paint and emulsion | ✓ Suitable |
| Plaster and render | ✓ Suitable |
| Mortar and screed (low speed) | ✓ Suitable at low speed |
| Tile adhesive (low speed) | ✓ Suitable at low speed |
| Wall materials generally | ✓ Suitable |
| Makita 18V LXT batteries (BL series) | ✓ Compatible |
| High-viscosity materials at high speed (mortar, adhesive) | ⚠ Not recommended — risk of loss of control |
| Flammable materials | ✗ Not suitable |
| Food processing | ✗ Not suitable |
| Non-Makita batteries | ✗ Not suitable — use only Makita LXT batteries listed above |
Who is this for
The Makita DUT130Z is used by plasterers, renderers, decorators, and tilers who need a portable, cable-free mixer for site and building interior work. It suits any professional who mixes materials regularly throughout the working day and needs consistent output without the constraints of a trailing cable or a fixed power supply. Operatives already using Makita 18V LXT tools on site can use existing batteries directly.
Typical applications
-
Mixing plaster and render to consistent working consistency before application to walls and ceilings.
-
Mixing tile adhesive and grout at low speed for controlled application without air entrainment.
-
Mixing paint and emulsion at high speed to achieve even pigment distribution before use.
-
Mixing self-levelling floor compounds to the correct viscosity for pouring.
-
Blending bagged mortar and screed materials at low speed in a mixing bucket on site.
How to use
Step 1: Fit the appropriate mixing blade to the M14 spindle thread. Ensure the blade is marked "UP" with the marking facing towards the tool body before tightening the hex bolt.
Step 2: Fit the front cover and tighten the side handle firmly to the tool body. The side handle can be positioned on either side.
Step 3: Install a fully charged Makita 18V LXT battery (BL1815N to BL1860B). Close the battery cover securely.
Step 4: Select the correct speed range using the speed change knob. Always do this with the tool fully stationary. Low speed (position 1) for mortar, adhesive, and high-viscosity materials. High speed (position 2) for paint, render, and thinner materials.
Step 5: Submerge the mixing blade fully in the material and place the mixing container on a firm, level surface before starting the tool.
Step 6: Press the trigger lock button from the A side, then squeeze the trigger. Speed increases with trigger pressure. Move the blade up and down during mixing to ensure all material is reached.
Step 7: For continuous operation, press the lock button while holding the trigger, then release the trigger. To stop in continuous mode, squeeze the trigger fully and release.
Step 8: When mixing is complete, switch the tool off and wait until the blade has stopped completely before lifting it from the material.
Step 9: After use, press the trigger lock from the B side to lock the trigger in the off position before removing the battery for storage or charging.
Common mistakes
-
Changing speed while the tool is running: The speed change knob must only be moved when the tool has fully stopped. Changing speed under load can damage the gearbox.
-
Running the blade outside the mixing container: Always start and stop the tool with the blade submerged in the material. Starting in open air can cause the blade to bend or spin uncontrolled.
-
Using high viscosity materials at high speed: Mortar, thick adhesive, and heavy screed should always be mixed at low speed. Using high speed with these materials risks losing control of the tool.
-
Operating with an incorrectly fitted battery: If the red indicator on the battery button is visible after fitting, the battery is not fully locked. A loose battery can fall during use.
-
Not fitting the front cover: The front cover minimises the risk of spattered material entering the battery compartment. Always fit it before mixing.
Safety
Wear ear protection during use. Sound pressure may exceed 80 dB(A) under working conditions. Wear appropriate PPE including eye protection and gloves when handling mixing materials. The vibration level is ≤ 2.5 m/s² (the Exposure Action Value under the Control of Vibration at Work Regulations 2005). Carry out a vibration risk assessment for operatives using this tool regularly. Do not use near flammable materials. Do not mix food. Ensure the mixing container is on a firm, stable surface before starting. Do not reach into the mixing container while the blade is moving.
Maintenance
Wipe clean after use. Do not use water, benzene, solvents, or alcohol, these can cause discolouration and cracking. Keep the battery contacts and battery compartment clean and free from debris. Store the tool with the battery removed when not in use for extended periods. All repairs and adjustments must be carried out by a Makita authorised service centre using genuine Makita parts.
Frequently Asked Questions
Q: What does "body only" mean for this paddle mixer?
A: Body only means the tool is sold without a battery, charger, or carry case. You need a Makita 18V LXT battery and a compatible Makita charger to operate it. If you already use Makita LXT tools on site, your existing batteries and charger will work directly. If you are new to the LXT platform, add the Makita Li-ion battery (MAKBAT4AH or MAKBAT5AH) and charger (MAKFC18) to your order.
Q: Which Makita batteries work with the DUT130Z?
A: The DUT130Z is compatible with the full Makita 18V LXT Li-ion battery range: BL1815N, BL1820B, BL1830B, BL1840B, BL1850B, and BL1860B. A higher capacity battery (4.0Ah or 5.0Ah) will give longer run time between charges on sustained mixing tasks. Only use genuine Makita LXT batteries, fitting non-compatible batteries can cause tool damage and voids the Makita warranty.
Q: What is the difference between the two speed settings?
A: Low speed (0-350 min⁻¹) is for high-viscosity materials including mortar, thick tile adhesive, and heavy screed. It provides controlled mixing with less risk of splashing and maintains safe handling of heavier materials. High speed (0-1,300 min⁻¹) is for paint, emulsion, render, and thinner materials where faster agitation is needed. The speed change knob must only be moved when the tool has fully stopped, never change speed while running.
Q: What is XPT technology?
A: XPT stands for eXtreme Protection Technology. It is Makita's engineering approach to improved dust and water resistance, designed for tools used in harsh site conditions. It does not replace taking reasonable precautions around water exposure, but it reduces the risk of dust and splatter entering the tool during normal site use.
Q: What mixing blade do I need?
A: The spindle thread is M14 (1/2"). CMT stocks the MP115M14 Heavy Duty Mixing Paddle, which has an M14 thread shank and a 115 x 600mm blade, this is the direct companion for the DUT130Z. The maximum compatible blade diameter is 165mm. Always fit the blade with the "UP" marking facing towards the tool before tightening the hex bolt.
Q: What materials is this NOT suitable for?
A: Not suitable for mixing flammable materials (paints containing thinners used as solvent, and similar). Not designed for food processing. Do not use at high speed for mortar, thick adhesive, or other high-viscosity materials, you risk losing control of the tool. Only use Makita-specified LXT batteries.
Q: What vibration and noise levels should operatives be aware of?
A: The declared vibration level is ≤ 2.5 m/s² (3-axis), which is at the Exposure Action Value under the Control of Vibration at Work Regulations 2005. Actual vibration during use may differ from this declared value. Sound pressure is 77 dB(A) and may exceed 80 dB(A) during use. Ear protection must be worn. Carry out a vibration risk assessment for operatives using this tool across extended periods.
