Powder coated steel mixing paddle for electric and cordless drills, for mixing paint, plaster, mortar, and cement.
- 100mm head, 600mm shaft length
- 10mm hex shank, fits standard 10mm drill chucks
- Powder coated steel for corrosion resistance
- Suitable for paint, plaster, render, mortar, and cement
- For use with electric and cordless drills only
- Sold as single paddle
Mixing Paddle 100 x 600mm - 10mm Hex for Drills
Powder coated steel mixing paddle for electric and cordless drills, for mixing paint, plaster, mortar, and cement.
- 100mm head, 600mm shaft length
- 10mm hex shank, fits standard 10mm drill chucks
- Powder coated steel for corrosion resistance
- Suitable for paint, plaster, render, mortar, and cement
- For use with electric and cordless drills only
- Sold as single paddle
- Buy 6 for £11.92 £9.93 each and save 9%
- Buy 12 for £10.50 £8.75 each and save 20%
| BULK DISCOUNT | 6 | 12 |
|---|---|---|
| Price | £9.93 £11.92 | £8.75 £10.50 |
Order 1x to earn 10 FASTPoints
Order to earn 10 FASTPoints
Log in to access trade discountsMixing Paddle 100 x 600mm
Steel mixing paddle for electric and cordless drills, designed for mixing paint, plaster, render, mortar, and cement. The 100mm head and 600mm shaft give enough reach to work in standard mixing buckets. The 10mm hex shank fits directly into a 10mm drill chuck with no adaptor needed.
Why powder coating matters for a mixing paddle
Bare steel corrodes quickly in contact with alkaline materials like cement, mortar, and plaster. After just a few uses, uncoated steel develops surface rust that can contaminate the material being mixed and degrades the paddle significantly faster than a protected alternative. The powder coated finish on this paddle creates a barrier between the steel and the mixing material, reducing corrosion and extending the working life of the tool.
Key Features
-
100mm head, 600mm shaft: Sized for standard mixing buckets. Long enough to reach the base of a bucket and wide enough to move material efficiently without excessive passes.
-
10mm hex shank: Fits directly into a standard 10mm keyless or keyed drill chuck. No adaptor required for most electric and cordless drills.
-
Powder coated steel: Corrosion-resistant finish protects the steel body against alkaline mixing materials including cement, mortar, and plaster.
-
Wide application range: Suitable for mixing paint, emulsion, plaster, render, tile adhesive, mortar, and cement in standard bucket and container sizes.
-
Single paddle: Sold as one paddle, order multiple units for multi-operative teams.
Who is this for
Trades and roles:
-
Decorators and painters
-
Plasterers and renderers
-
Tilers and floor layers
-
Bricklayers and groundworkers
Industries:
-
Construction
-
Decorating and finishing
-
Tiling and floor laying
Specifications
| Specification | Detail |
|---|---|
| Product Name | Mixing Paddle 100 x 600mm - 10mm Hex for Drills |
| SKU | MP10600 |
| Brand | Draper |
| Type | Mixing paddle |
| Head Diameter | 100mm |
| Shaft Length | 600mm |
| Shank | 10mm hex |
| Material | Steel |
| Finish | Powder coated — corrosion protection |
| Compatible Tools | Electric and cordless drills with 10mm chuck |
| Applications | Paint, plaster, render, mortar, cement |
Compatibility
| Application or condition | Status |
| Electric drills with 10mm chuck | ✓ Compatible |
| Cordless drills with 10mm chuck | ✓ Compatible |
| Paint and emulsion | ✓ Suitable |
| Plaster and render | ✓ Suitable |
| Mortar and cement | ✓ Suitable |
| M14 thread paddle mixers (e.g. Makita DUT130Z) | ✗ Not compatible — different shank type |
| SDS drills | ✗ Not compatible — different shank type |
| Impact drivers | ✗ Not suitable — not designed for mixing |
Who is this for
This paddle is used by decorators, plasterers, tilers, and site operatives who need a drill-powered mixing attachment for small to medium mixing tasks. It suits any trade that mixes paint, plaster, adhesive, mortar, or cement regularly using an electric or cordless drill rather than a dedicated paddle mixer. It is the right tool where portability and low cost matter more than the high-torque mixing capacity of a dedicated machine.
Typical applications
-
Mixing paint and emulsion to an even consistency before applying to walls and ceilings.
-
Mixing plaster to working consistency in a bucket before plastering small areas.
-
Mixing tile adhesive and grout to the correct viscosity for floor and wall tiling.
-
Mixing bagged mortar for pointing and small bricklaying tasks.
-
Mixing self-levelling compounds in small batches for floor repairs.
How to use
Step 1: Insert the 10mm hex shank into the drill chuck. Tighten the chuck fully and confirm the paddle is secure before starting.
Step 2: Submerge the paddle head fully in the material before starting the drill. Never run the paddle in open air — it can whip and cause injury.
Step 3: Start at a low speed and increase progressively. Keep the paddle submerged throughout the mixing session.
Step 4: Move the paddle steadily up and down to work the material from the base of the container to the top. Continue until the mix is even and consistent.
Step 5: Stop the drill fully before lifting the paddle out of the material.
Step 6: Rinse the paddle immediately after use with clean water. Remove all material before it sets on the paddle surface.
Common mistakes
-
Running the paddle in open air: Starting the drill before the paddle is fully submerged causes the paddle to spin uncontrolled and can cause the shaft to whip, risking injury and damage.
-
Using with an impact driver: Impact drivers are not suitable for mixing. The hammering action can damage the paddle and the driver. Use only with rotary drills.
-
Using with an SDS drill: The 10mm hex shank is not compatible with SDS chuck fittings. Use only with a 10mm standard drill chuck.
-
Leaving material to set on the paddle: Cement and mortar harden rapidly. Rinse immediately after every use, hardened material is very difficult to remove and shortens the paddle's working life.
Safety
Keep hands away from the rotating paddle at all times. Ensure the mixing container is on a firm, stable surface before starting the drill. Never operate the paddle in open air. Wear eye protection to guard against splashing. Follow the maximum RPM specification for this paddle (confirm from the product data sheet before use). Do not use with impact drivers or SDS drills.
Maintenance
Rinse in clean water after every use. Remove all material before it sets. Allow to dry and store in a clean, dry location. Inspect the shaft for bending and the head for deformation before each use. Replace if the shaft is bent or the paddle head is significantly distorted, a bent paddle produces inconsistent mixing and can vibrate dangerously.
Frequently Asked Questions
Q: What size drill chuck does this fit?
A: The 10mm hex shank fits directly into a standard 10mm drill chuck, either keyless or keyed. No adaptor is needed for most electric and cordless drills with a 10mm chuck capacity.
Q: Is this compatible with the Makita DUT130Z paddle mixer?
A: No. The DUT130Z uses an M14 thread spindle. This paddle has a 10mm hex shank, which is a completely different fitting. For the DUT130Z, use the MP115M14 Heavy Duty Mixing Paddle, which has the correct M14 thread connection.
Q: Can I use this with an SDS drill or impact driver?
A: No. The 10mm hex shank is designed for standard 10mm drill chucks only. SDS drills use a different chuck system and are not compatible. Impact drivers are not designed for mixing tasks, the impact mechanism is not suitable and risks damaging both the driver and the paddle.
Q: What materials can this mix?
A: This paddle is suitable for paint, emulsion, plaster, render, tile adhesive, grout, mortar, and cement. It is sized for standard mixing bucket tasks rather than large-volume continuous mixing.
Q: Why is powder coating better than uncoated steel for a mixing paddle?
A: Cement, mortar, and plaster are alkaline materials that accelerate corrosion on bare steel. Powder coating creates a barrier between the steel and the material, reducing surface rust and extending the working life of the paddle. Uncoated steel paddles corrode quickly under regular site use.
Q: How should I clean this paddle after use?
A: Rinse with clean water immediately after each use. Remove all material before it has a chance to set on the paddle surface. Cement and plaster harden quickly. Once set, they are very difficult to remove without risking damage to the paddle.
