MAX Double Leather Palm Rigger Gloves - Heavy Duty Construction and General Handling

MAX Double Leather Palm Rigger Gloves

The MAX Double Leather Palm Rigger Glove is a robust, site-ready work glove built for the demanding end of general construction, metal handling, and maintenance work. Where a standard single-layer rigger glove concentrates wear on the palm and thumb face until the leather thins and fails, the MAX uses two layers of well-tanned contrast-coloured leather applied across the palm, around the forefinger, and across the thumb face: the three areas that take the most punishment in heavy handling tasks. The heavy-weight fabric back and fleece palm liner add warmth and comfort for outdoor use without restricting the natural movement of the hand. The result is a glove that is substantially more durable than a single-layer alternative at the same price point, reducing replacement frequency and per-operative cost over a project. Available in XL only, supplied in packs of 12 pairs.

Why choose the MAX Double Leather Palm Rigger Gloves

• Double leather where it matters most: Two layers of tanned leather across the palm, forefinger, and thumb face targets reinforcement at the exact points that wear through first on a single-layer rigger, extending working life substantially.

• Tough yet supple leather construction: Well-tanned leather retains flexibility during use, avoiding the stiffness that cheap or poorly-tanned alternatives develop after the first shift, which forces operatives to remove gloves to maintain grip.

• Heavy-weight fabric back with fleece liner: The combination of durable fabric on the back and a warm fleece palm liner makes this a practical choice for cold-weather outdoor construction and site work where comfort over a full shift matters.

• Dexterity is not compromised: The cut and panel construction allow natural hand movement, meaning the glove can be worn continuously during tool use, material handling, and general site tasks without the restriction that some rigger styles introduce.

• EN 388 certified: Independently tested and certified to the mechanical protection standard, providing a defensible specification basis for PPE risk assessments.

• CMT own-brand value: The MAX range is manufactured under CMT Group's own brand, providing direct supply chain control and consistent quality at a competitive pack price for bulk site procurement.

• Pack of 12 for site store efficiency: The 12-pair pack format suits site stores, welfare cabin stock, and framework procurement without requiring individual pair ordering.

What's included

12 x pairs of MAX Double Leather Palm Rigger Gloves in size XL.

 Specifications

Compatibility

Who is this for?

The MAX Double Leather Palm Rigger Glove is specified by site managers, groundworkers, steelfixers, scaffolders, general operatives, and procurement teams on construction, civil engineering, metal handling, and transportation projects where sustained heavy-duty manual work demands a glove that outlasts single-layer alternatives. The XL size and 12-pair pack format suits site stores and welfare cabin stock where a single size covers the majority of the workforce and bulk pricing reduces per-operative PPE cost across a project.

Typical applications

• Heavy material handling on construction and civils sites involving concrete blocks, steel sections, timber, and aggregates

• Metal handling and fabrication tasks where the double leather palm provides grip and abrasion resistance against sharp edges and rough metal surfaces

• Scaffolding erection and dismantling where sustained grip on tubes and couplers requires a durable, non-slip palm surface

• General maintenance tasks involving rough surfaces, fixings, and hand tools across construction, utilities, and industrial sites

• Transportation and logistics loading and unloading where sustained grip and palm protection are required throughout a shift

• Cold-weather outdoor construction work where the fleece palm liner provides warmth without bulk or restriction

How to use

1. Confirm size XL is appropriate before issuing. These gloves are available in XL only.

2. Inspect the glove before each use. Check the leather palm for cuts, thinning, or separation at the stitching. Discard any glove showing these defects.

3. Don the glove ensuring the leather palm panel seats correctly across the palm, forefinger, and thumb face.

4. Use for heavy-duty construction, metal handling, maintenance, and transportation tasks. Not suitable for precision work, heat exposure, chemical contact, or electrical hazards.

5. Remove promptly when significant wear or damage is identified. A worn leather palm provides reduced protection and should be replaced before continuing heavy-duty tasks.

6. Wash hands thoroughly before donning and after removing gloves.

Safety

• EN 388 certified for mechanical protection. Not rated for heat, cut protection beyond the EN 388 score, chemical protection, or electrical hazards.

• Leather degrades with prolonged water exposure. Do not use in submerged or continuously wet conditions.

• Not suitable for precision or fine assembly tasks where dexterity beyond the rigger format is required.

• If a skin reaction occurs during use, remove immediately and seek medical advice.

Maintenance

Allow wet leather to dry naturally at room temperature away from direct heat sources. Do not place on a radiator or in direct sunlight to dry as this causes the leather to stiffen and crack. Brush off dried mud and debris before storing. Inspect the stitching at the palm panel edges and cuff after each shift. Store in a dry, ventilated area away from direct sunlight. Discard when the leather palm shows significant thinning, cracking, or stitching failure.

Frequently Asked Questions

Q: What does the double leather palm actually mean in practice?

 A: Two separate layers of tanned leather are applied across the palm, around the forefinger, and across the thumb face. These are the three areas that take the most sustained contact and abrasion in heavy handling tasks. A single-layer rigger glove concentrates wear on these points until the leather thins and fails. The double layer significantly extends the working life of the glove before replacement is needed, reducing per-operative PPE cost over a project.

Q: Why is this glove only available in XL?

 A: The MAX Double Leather Palm Rigger Glove is positioned as a bulk site store product for general operative issue where a single size covers the majority of the workforce. XL is the most commonly issued size in UK construction site environments. If smaller or larger sizes are required, alternative rigger gloves in the CMT range are available in a full size run.

Q: Is this glove warm enough for outdoor winter construction work?

 A: Yes. The heavy-weight fabric back and fleece palm liner provide meaningful warmth for cold-weather outdoor work. It is not an insulated thermal glove and will not provide protection in extreme cold, but for typical UK winter site conditions it provides adequate warmth without the bulk of a dedicated cold-weather glove.

Q: Does leather degrade in wet conditions?

 A: Incidental contact with rain and moisture during normal outdoor site work will not cause significant damage. Prolonged immersion or continuous wet conditions will cause the leather to soften, lose structural integrity, and dry stiff. Allow wet gloves to dry naturally at room temperature. Do not use these gloves for tasks involving sustained water contact.

Q: What is the EN 388 certification and why does it matter for site PPE?

 A: EN 388 is the European standard for gloves providing protection against mechanical risks including abrasion, cut, tear, and puncture. Certification confirms the glove has been independently tested to the standard's requirements. For site PPE risk assessments, specifying an EN 388 certified rigger glove provides a defensible audit trail confirming the product meets the mechanical protection requirements identified in the assessment.

Q: How does this compare to a single-layer rigger glove?

 A: A standard single-layer rigger glove uses one layer of leather across the palm. The MAX uses two layers at the highest-wear points. The practical result is a glove that lasts significantly longer in heavy-duty tasks before the palm wears through, reducing replacement frequency and the associated cost and administrative burden on site stores. For light or occasional use, a single-layer rigger is sufficient. For sustained heavy-duty construction and metal handling tasks, the double-layer construction is the more cost-effective choice over the life of a project.

Q: Can this glove be used for scaffolding work?

 A: Yes. The double leather palm and thumb reinforcement provide the grip and durability required for sustained tube and coupler handling during scaffolding erection and dismantling. The dexterity is not compromised by the construction, allowing normal hand movement during fitting and adjustment.

Q: Why buy MAX rigger gloves from CMT Group?

 A: CMT Group is a BSIF Registered Safety Supplier and holds ISO 9001:2015, CHAS Elite, and SSIP accreditations, meaning PPE products are sourced through a verified, compliant supply chain. The MAX range is CMT's own brand, providing direct quality control and consistent specification across every pack. Most orders are despatched for same or next working day UK mainland delivery when placed by 7pm online. The 12-pair pack format suits both single-site orders and framework procurement with volume pricing available through CMT's EDGE procurement portal.