Anti-microbial tacky mat with 30 peel-off layers, designed to trap dirt and dust from footwear and wheeled equipment entering cleanrooms and laboratories.
- 30 peel-off layers per mat, fresh clean surface every time
- Anti-microbial adhesive surface, suitable for medical and clean zones
- Slip resistance Level 2 and wear resistance Level 2
- Suitable for wheeled trolleys and foot traffic
- Bottom layer adheres securely to clean, dry floors
- For indoor, dry area use only
- Supplied 4 mats per pack
- 900 x 600mm
Tacky Mat Blue 600 x 900mm - Anti-Microbial 30 Layer Peel-Off Matting
Anti-microbial tacky mat with 30 peel-off layers, designed to trap dirt and dust from footwear and wheeled equipment entering cleanrooms and laboratories.
- 30 peel-off layers per mat, fresh clean surface every time
- Anti-microbial adhesive surface, suitable for medical and clean zones
- Slip resistance Level 2 and wear resistance Level 2
- Suitable for wheeled trolleys and foot traffic
- Bottom layer adheres securely to clean, dry floors
- For indoor, dry area use only
- Supplied 4 mats per pack
- 900 x 600mm
- Buy 10 for £58.20 £48.50 each and save 12%
- Buy 25 for £51.00 £42.50 each and save 23%
| BULK DISCOUNT | 10 | 25 |
|---|---|---|
| Price | £48.50 £58.20 | £42.50 £51.00 |
Order 1x to earn 54 FASTPoints
Order to earn 54 FASTPoints
Log in to access trade discountsTacky Mat Blue 600 x 900mm - 30 Layer Peel-Off Matting
Anti-microbial tacky mat built with 30 peel-off layers to trap dirt and dust before it reaches a cleanroom, laboratory, or pharmaceutical production area. Foot traffic and wheeled trolleys pick up contamination on the way in, this mat strips it off on contact and holds it in the adhesive layer rather than letting it spread further. Each layer peels away to reveal a fresh surface underneath, so the mat stays fully effective without needing a full replacement.
How peel-off layers keep contamination control consistent
A single-layer dust mat loses effectiveness as it gets dirty, and busy sites often don't notice until contamination has already spread. That gap between a mat looking clean and actually working is where cross-contamination risk creeps into cleanrooms and labs. With 30 peel-off layers, staff simply strip off the top sheet once it's visibly dirty, restoring full tack instantly without waiting for a mat change or a cleaning cycle.
Key Features
-
30 peel-off layers: Each mat carries 30 numbered adhesive sheets, so a fresh, fully effective surface is always one peel away.
-
Anti-microbial adhesive: Removes dirt and dust from shoes and wheels on contact, and is rated suitable for medical and clean zone use.
-
Dual peel adhesion strength: Top layers hold at 433g/25mm for effective dirt pickup, while the bottom layer bonds at 1071g/25mm to stay firmly fixed to the floor.
-
Slip resistance Level 2: Rated for safe use in areas with foot traffic and wheeled equipment.
-
Low profile 2mm height: Sits flush enough not to create a trip hazard or obstruct trolley wheels.
-
Wheeled equipment compatible: Designed to withstand repeated trolley and cart traffic without lifting or shifting.
Who is this for
Trades and roles:
-
Cleanroom operatives
-
Laboratory technicians
-
Pharmaceutical production staff
-
Facilities and hygiene managers
-
Manufacturing quality control teams
Industries:
-
Pharmaceutical manufacturing
-
Life sciences and laboratories
-
Aerospace and specialist manufacturing
-
Healthcare and medical facilities
-
Electronics and cleanroom manufacturing
Specifications
| Specification | Detail |
| Product Name | Tacky Mat Blue 600 x 900mm - Anti-Microbial 30 Layer Peel-Off Matting |
| SKU | TCKMAT |
| Manufacturer | Blue Diamond |
| Mat Type | Anti-microbial peel-off contamination control mat |
| Number of Layers | 30 per mat |
| Sheet Thickness | 0.055mm ± 5% |
| Peel Adhesion, Top Layer | 433g/25mm |
| Peel Adhesion, Bottom Layer | 1071g/25mm |
| Overall Height | 2mm |
| Slip Resistance | Level 2 |
| Wear Resistance | Level 2 |
| Suitable Environments | Cleanrooms, laboratories, pharmaceutical areas, specialist manufacturing |
| Area Type | Dry areas only, indoor use |
| Mat Size | 600 x 900mm |
| Colour | Blue |
| Pack Quantity | 4 mats per pack |
Compatibility
| Application or condition | Status |
| Cleanrooms and laboratories | Compatible |
| Pharmaceutical and medical clean zones | Compatible |
| Wheeled trolley and cart traffic | Compatible |
| Dry indoor floor areas | Compatible |
| Wet or outdoor areas | Not recommended |
| Heavy vehicle or forklift traffic | Not recommended |
| Uneven or textured flooring | Not recommended |
Who is this for
This mat suits facilities where contamination control at the entry point genuinely matters, cleanroom operators, laboratory managers, and pharmaceutical production teams working to strict dust and particle standards. It's equally relevant to aerospace and specialist manufacturing sites where a single contaminated component can cause a costly rework or failure.
Typical applications
-
Positioning at cleanroom and laboratory entry points to remove contamination from footwear.
-
Placing beneath wheeled trolleys and carts moving between production zones.
-
Supporting pharmaceutical manufacturing areas working to strict particle control standards.
-
Protecting aerospace and specialist manufacturing environments from foot-borne contamination.
-
Maintaining hygiene standards in medical and clean zone facilities.
-
Controlling dust transfer between general production floors and controlled environments.
How to use
Step 1: Choose a clean, dry, flat area at the entry point to the controlled environment.
Step 2: Remove the protective backing from the bottom layer and press the mat firmly onto the floor.
Step 3: Allow foot traffic and wheeled equipment to pass directly over the mat on entry.
Step 4: Peel off the top layer once it's visibly dirty or loses tack, revealing a fresh layer underneath.
Step 5: Replace the full mat once all 30 layers have been used.
Common mistakes
-
Applying to a dirty or uneven floor: the bottom layer needs a clean, flat, dry surface to bond securely, otherwise the mat can lift or shift under traffic.
-
Leaving a dirty layer in place too long: waiting too long to peel off a saturated layer reduces how much new contamination it can trap.
-
Using it in wet or outdoor areas: this mat is rated for dry indoor use only, moisture affects adhesion and mat performance.
-
Assuming it replaces PPE or cleaning protocols: the mat reduces contamination transfer, it doesn't replace existing site hygiene procedures.
Safety
This mat is rated for slip resistance Level 2 and wear resistance Level 2, suitable for foot traffic and wheeled equipment in dry indoor areas. It is not rated for wet, outdoor, or heavy vehicle use. The anti-microbial adhesive is suitable for medical and clean zone environments but doesn't replace site-specific hygiene or infection control protocols.
Maintenance
Peel off each layer once it's visibly dirty or loses tack, rather than leaving a saturated layer in place. Replace the full mat once all 30 layers have been used. Store spare mats flat, in a clean, dry area away from direct sunlight.
Frequently Asked Questions
Q: How does a peel-off tacky mat actually work?
A: Each mat is built from 30 adhesive layers stacked on top of each other. As footwear or wheeled equipment passes over the top layer, the anti-microbial adhesive picks up dirt, dust, and debris on contact. Once that layer looks dirty or loses its tack, staff peel it away to reveal a fresh, fully effective layer underneath, no cleaning or replacement needed until all 30 layers are used.
Q: What does "anti-microbial" mean for this mat, and why does it matter?
A: The adhesive surface is treated to inhibit microbial growth, which matters in medical, pharmaceutical, and clean zone environments where bacterial contamination is a genuine risk, not just a dirt issue. This is separate from the mat's dirt-trapping function, a standard tacky mat removes debris, but an anti-microbial one is rated safe for use where hygiene standards go beyond just keeping floors clean.
Q: What is this mat NOT suitable for?
A: It's rated for dry indoor areas only, not wet, outdoor, or heavily contaminated floors. It isn't designed for heavy vehicle or forklift traffic, only foot traffic and wheeled trolleys or carts. The adhesive also needs a clean, flat, dry surface to bond properly, an uneven or dirty floor will reduce how well the mat stays in place.
Q: Why choose a 30 layer mat over a standard entrance mat?
A: A standard entrance mat traps some dirt but needs regular cleaning to stay effective, and it's easy for staff to miss when it's overdue. A 30 layer tacky mat gives an instant, visible reset, peel off the dirty layer and the next one is immediately at full tack, with no cleaning cycle or guesswork about when it needs attention.
Q: How long does one mat last before it needs replacing?
A: That depends on foot and wheeled traffic volume, a high-traffic cleanroom entrance will use up layers faster than a low-traffic lab. Once all 30 layers have been peeled away, the full mat needs replacing, keeping a few spares on hand avoids a gap in contamination control.
Q: Can this mat be used with wheeled trolleys as well as foot traffic?
A: Yes. It's designed to withstand repeated trolley and cart traffic without lifting or shifting, provided the floor underneath is clean, flat, and dry. It isn't rated for heavier vehicles like forklifts.
