Triple-dipped nitrile cut resistant gauntlet built for chemical handlers, oil and gas operatives, and waste and recycling workers requiring TDM Level E cut protection alongside oilproof and waterproof liquid resistance.
- TDM Cut Level E, ISO 13997 straight-blade tested, EN388:2016+A1:2018 rated 4X44E
- EN ISO 374-1:2016+A1:2018 Type B, CE marked CAT III, chemicals K, P, T
- Triple-dipped nitrile, oilproof and waterproof entire hand and forearm
- 18-gauge HPPE, steel fibre, and nylon composite liner
- Foam nitrile palm over nitrile outer, wet, oily, and chemical grip
- Extended gauntlet cuff, open cuff for easy donning and doffing
- Touchscreen compatible
- Available in bulk packs
Skytec Triple-Dipped Nitrile Cut Level E Cut Resistant Gauntlet - Chemical and Oily Handling
Triple-dipped nitrile cut resistant gauntlet built for chemical handlers, oil and gas operatives, and waste and recycling workers requiring TDM Level E cut protection alongside oilproof and waterproof liquid resistance.
- TDM Cut Level E, ISO 13997 straight-blade tested, EN388:2016+A1:2018 rated 4X44E
- EN ISO 374-1:2016+A1:2018 Type B, CE marked CAT III, chemicals K, P, T
- Triple-dipped nitrile, oilproof and waterproof entire hand and forearm
- 18-gauge HPPE, steel fibre, and nylon composite liner
- Foam nitrile palm over nitrile outer, wet, oily, and chemical grip
- Extended gauntlet cuff, open cuff for easy donning and doffing
- Touchscreen compatible
- Available in bulk packs
Skytec Triple-Dipped Nitrile Cut Level E Cut Resistant Gauntlet
Triple-dipped nitrile cut resistant gauntlets designed for chemical handlers, oil and gas operatives, waste and recycling workers, and industrial maintenance professionals requiring TDM Cut Level E protection alongside oilproof liquid resistance and chemical splash protection. The 18-gauge HPPE, steel fibre, and nylon composite liner achieves TDM Level E under ISO 13997, whilst the triple-dipped nitrile construction provides oilproof, waterproof coverage from fingertip to forearm. Certified to EN388:2016+A1:2018 rated 4X44E, EN ISO 374-1:2016+A1:2018 Type B (chemicals K, P, T), EN ISO 374-5:2016+A1:2018 for micro-organisms, and EN407:2020 rated X1XXXX. CE marked CAT III, the highest PPE risk classification under UK PPE Regulations.
How triple-dipped nitrile delivers oilproof cut protection where standard gauntlets fail
A standard single or double-dipped nitrile gauntlet thins at the fingertips and along the knuckle line through normal handling contact. In sustained exposure to oils, fuels, and chemical splash, those thinner areas allow liquid penetration before the end of a shift. A cut resistant liner alone provides no liquid barrier. Triple-dipping builds three nitrile layers progressively across the hand and forearm surface, reinforcing the areas of highest wear and creating a liquid barrier that withstands sustained oily and chemical splash exposure throughout the working day, whilst the HPPE and steel fibre composite liner maintains TDM Level E cut protection beneath the coating at all times.
Key Features
-
Triple-dipped nitrile construction: Three nitrile layers applied progressively across the complete hand and forearm surface. Provides oilproof and waterproof protection against sustained liquid exposure, oil submersion, and chemical splash in environments where single or double-dipped alternatives fail prematurely.
-
TDM Cut Level E liner: 18-gauge HPPE, steel fibre, and nylon composite liner achieves TDM Level E under ISO 13997 straight-blade testing. Steel fibre in the yarn adds cut resistance at the liner stage without requiring a heavier gauge, maintaining dexterity for handling tasks in chemical and industrial environments.
-
EN ISO 374-1:2016+A1:2018 Type B chemical protection: Certified against chemical permeation for chemicals K (cyclohexane), P (1-pentanol), and T (toluene). Type B classification covers splash protection and partial immersion scenarios relevant to chemical handling, oil and gas maintenance, and industrial cleaning tasks.
-
EN ISO 374-5:2016+A1:2018 micro-organism protection: Certified for protection against micro-organisms, relevant for waste and recycling operatives and facilities management workers handling contaminated materials.
-
Extended gauntlet cuff: 270mm total length with an open gauntlet cuff provides forearm protection against liquid run-back, chemical splash, and sharp material contact above the wrist. Open cuff construction allows rapid donning and doffing without contaminating the inner surface.
-
Foam nitrile palm grip: The foam nitrile palm layer creates a textured grip surface that maintains purchase on wet, oily, and chemically contaminated components throughout a full shift without over-gripping or hand fatigue.
-
CAT III classification: The highest risk category under UK PPE Regulations. CAT III products protect against serious or mortal risk and require independent third-party assessment before CE marking, confirming this gauntlet meets the most stringent compliance requirements for high-risk industrial environments.
Who is this for
Trades and roles:
-
Chemical handling operatives
-
Oil and gas maintenance workers
-
Waste and recycling operatives
-
Industrial maintenance engineers
-
Facilities management operatives
Industries:
-
Chemicals
-
Oil and gas
-
Waste and recycling
-
Construction
-
Manufacturing
-
Facilities management
Specifications
| Specification | Detail |
| Product name | Skytec Triple-Dipped Nitrile Cut Level E Cut Resistant Gauntlet - Chemical and Oily Handling |
| SKU / product code | TRC760 |
| Glove category | Cut resistant oilproof chemical gauntlet |
| Primary protection type | Cut resistant TDM Cut Level E, oilproof, waterproof, chemical splash |
| Risk category | CAT III, highest risk classification under UK PPE Regulations |
| EN mechanical standard | EN388:2016+A1:2018 |
| EN388 rating code | 4X44E |
| Abrasion resistance | Level 4 |
| Coupe blade cut resistance | X, not tested / unreliable result |
| Tear resistance | Level 4 |
| Puncture resistance | Level 4 |
| TDM cut resistance (ISO 13997) | Level E |
| Impact protection | Not tested |
| EN chemical standard | EN ISO 374-1:2016+A1:2018 |
| Chemical protection type | Type B, splash protection |
| Chemicals tested (K, P, T) | K: cyclohexane, P: 1-pentanol, T: toluene |
| Micro-organism standard | EN ISO 374-5:2016+A1:2018 |
| Thermal standard | EN407:2020 |
| EN407 rating code | X1XXXX |
| Contact heat resistance | Level 1, protection to 100°C for up to 15 seconds |
| Coating type | Triple-dipped, foam nitrile palm over nitrile outer |
| Coating coverage | Fully coated, fingertip to gauntlet cuff |
| Waterproof protection | Yes, oilproof and waterproof |
| Oil submersible | Yes |
| Grip performance | Wet, oily, and chemically contaminated conditions |
| Liner material | 18-gauge HPPE, nylon, steel fibre |
| Liner construction | Seamless knit |
| Cuff style | Extended open gauntlet cuff |
| Touchscreen compatible | Yes |
| Pack quantity | 10 pairs per pack |
| Colour | Green liner / black nitrile coating |
Compatibility
| Application or condition | Status |
| Chemical splash handling, Type B scenarios | ✓ Compatible |
| Oily and wet handling, oil submersion | ✓ Compatible |
| Sharp and abrasive material handling | ✓ Compatible |
| Waste and recycling sharp material handling | ✓ Compatible |
| Oil and gas maintenance tasks | ✓ Compatible |
| Industrial cleaning and maintenance | ✓ Compatible |
| Micro-organism exposure environments | ✓ Compatible |
| Incidental contact with warm surfaces to 100°C (max 15 seconds) | ✓ Compatible |
| Touchscreen device operation | ✓ Compatible |
| Full chemical immersion or Type A chemical protection | ✗ Not recommended, Type B splash only |
| Sustained heat or open flame exposure | ✗ Not recommended |
| Very high cut risk tasks, power cutting, blade grinding | ✗ Not recommended, use TDM Level F |
| Electrical hazard work | ✗ Not recommended |
| Needle-stick or hypodermic hazards | ✗ Not recommended, EN388 puncture is not needle-stick |
| Use near moving machinery with entanglement risk | ✗ Not recommended |
Who is this for
Triple-dipped nitrile cut resistant gauntlets at this specification are used primarily by chemical handling operatives, oil and gas maintenance workers, and waste and recycling professionals who face simultaneous cut hazard and liquid exposure throughout their working shift. The EN ISO 374-1 Type B chemical certification and EN388 TDM Level E cut rating make this gauntlet suited to environments where standard cut gloves provide no chemical protection and standard chemical gauntlets provide no meaningful cut resistance. Procurement teams specifying CAT III PPE for high-risk industrial environments will find this gauntlet meets the requirements of both the Personal Protective Equipment at Work Regulations 1992 and COSHH Regulations 2002 for the relevant hazard combination.
Typical applications
-
Chemical splash handling tasks in manufacturing and industrial environments where operatives handle containers, pipework, and equipment contaminated with oils, solvents, and industrial chemicals.
-
Oil and gas maintenance tasks involving sustained hand contact with oily pipework, valves, and machinery components where both oilproof grip and cut protection are required simultaneously.
-
Waste and recycling operative tasks involving mixed sharp materials, contaminated packaging, broken glass offcuts, and liquid-contaminated waste in environments where micro-organism exposure is also present.
-
Industrial cleaning and maintenance tasks where sharp-edged equipment, pipework, and fixings are handled in the presence of cleaning chemicals, oils, and liquid contamination.
-
Construction maintenance and facilities management tasks involving sharp materials and chemical contact, including drainage, utilities access, and confined space maintenance.
-
General multi-purpose sharp material handling in chemical, oil and gas, and manufacturing environments where a single gauntlet must address cut, liquid, and chemical hazards simultaneously.
How to use
Step 1: Select the correct size. XS fits hand size 6, S fits 7, M fits 8, L fits 9, XL fits 10, XXL fits 11, XXXL fits 12. Correct sizing is critical for a gauntlet. An oversized gauntlet allows liquid run-back at the wrist and reduces grip precision on oily components.
Step 2: Inspect the nitrile coating thoroughly before each use. Check the fingertips, palm, knuckle line, back of hand, and the gauntlet cuff for any cracking, pinholing, or breach in the coating. A single breach in the nitrile layer breaks both the oilproof and chemical protection barriers.
Step 3: Pull the gauntlet fully over the hand and up the forearm. Ensure the open gauntlet cuff seats correctly against the forearm without folding, which would create a channel for liquid ingress during handling tasks.
Step 4: When doffing after chemical or oily handling, grasp the outside of the gauntlet at the wrist area. Peel away from the hand without touching the contaminated outer surface. Use the gloved hand to remove the second gauntlet by sliding an ungloved finger under the cuff from the inside.
Step 5: After use, wipe with a damp cloth to remove chemical residue, oil, and contamination. Do not use solvent-based cleaners. Air dry fully before storing. Do not wash. These gauntlets are not washable.
Step 6: Replace when any cracking, pinholing, swelling, or discolouration of the nitrile coating is visible, or when grip performance on oily surfaces drops noticeably.
Common mistakes
-
Assuming Type B covers full immersion: EN ISO 374-1 Type B certifies splash protection and partial immersion scenarios only. Operatives whose hands are fully submerged in chemical solutions require Type A rated gloves.
-
Using for electrical hazard work: Nitrile provides no dielectric protection. These gauntlets carry no electrical insulation rating and must never be used against electrical hazards.
-
Incorrect doffing after chemical exposure: Pulling from the fingertips risks contact between the contaminated outer surface and the skin. Always doff from the wrist as described above.
-
Leaving chemical residue on the coating: Some industrial chemicals degrade nitrile over time even after the exposure event. Wipe clean after every use and inspect for swelling, tackiness, or discolouration before reuse.
-
Selecting the wrong size: An oversized gauntlet allows liquid to run inside the cuff during overhead work. Size correctly to ensure the cuff seats against the forearm.
-
Using near moving machinery: The gauntlet construction creates an entanglement risk near rotating parts and moving plant. Do not use where entanglement is possible.
Safety
These gauntlets are certified to EN388:2016+A1:2018 (4X44E), EN ISO 374-1:2016+A1:2018 Type B (K, P, T), EN ISO 374-5:2016+A1:2018, and EN407:2020 (X1XXXX) under UK PPE Regulations, CAT III. CAT III is the highest risk classification, covering protection against serious or mortal risk. Chemical protection is Type B splash only, not suitable for full chemical immersion scenarios requiring Type A protection. The EN407 contact heat rating covers incidental contact to 100°C for a maximum of 15 seconds only. These gauntlets are not suitable for electrical hazard work. Avoid use near moving machinery where entanglement is a risk. A COSHH assessment under the Control of Substances Hazardous to Health Regulations 2002 and a task-specific risk assessment under the Personal Protective Equipment at Work Regulations 1992 should both confirm suitability before use.
Maintenance
Wipe with a damp cloth after each use. These gauntlets are not washable. Do not machine wash or immerse in water for cleaning. Air dry fully before storing. Store in dry conditions between 10°C and 30°C, away from direct sunlight, heat sources, ozone, and chemical vapour. Do not exceed 40°C storage temperature. Inspect the full nitrile coating surface, including the gauntlet cuff and back of hand, before every shift. Check for swelling, tackiness, discolouration, pinholing, or cracking. Any of these indicate chemical degradation of the nitrile and the gauntlet must be replaced. When stored correctly, mechanical properties will not change for up to three years from the date of manufacture.
Frequently Asked Questions
Q: What is the difference between EN ISO 374-1 Type A, Type B, and Type C chemical protection, and which type does this gauntlet provide?
A: EN ISO 374-1 classifies chemical protective gloves into three types based on the level of resistance to chemical permeation. Type C covers minimal splash risk only. Type B, which this gauntlet holds, covers splash protection and partial immersion scenarios, the glove has been tested and confirmed to resist permeation by at least three chemicals for a minimum breakthrough time of 30 minutes. Type A covers full immersion and extended chemical exposure scenarios, requiring testing against at least six chemicals with a minimum 30-minute breakthrough time. For tasks involving chemical splash, handling of chemical-contaminated equipment, and partial immersion, Type B is the correct and sufficient specification. For tasks involving sustained full-hand immersion in chemical solutions, Type A rated gloves are required.
Q: What does the EN388:2016+A1:2018 rating of 4X44E mean?
A: EN388 is the UK standard for gloves protecting against mechanical risks. The first digit (4) is abrasion resistance at the maximum Level 4. The second position (X) means the Coupe rotating blade test was not conducted or returned an unreliable result, standard for gloves containing steel fibre composite liners, and not a failure. The third digit (4) is tear resistance at the maximum Level 4. The fourth digit (4) is puncture resistance at the maximum Level 4. The fifth position (E) is the TDM straight-blade cut result under ISO 13997, Level E, the second highest on the A to F scale. This is the definitive cut rating for RAMS and risk assessment documentation. CAT III CE marking confirms independent third-party assessment for serious risk protection under UK PPE Regulations.
Q: What are these gauntlets NOT suitable for?
A: These gauntlets are not suitable for full chemical immersion requiring Type A protection, Type B covers splash and partial immersion only. They are not rated for electrical hazard work and carry no dielectric protection. They are not suitable for sustained heat, open flame, or temperatures above 100°C beyond incidental 15-second contact. They must not be used for the highest cut risk tasks where TDM Level F is required. They are not needle-stick resistant. They must not be used near moving machinery where entanglement is a risk.
Q: Which specific chemicals are these gauntlets tested and certified against?
A: Under EN ISO 374-1:2016+A1:2018 Type B, this gauntlet is certified against three specific chemicals: K (cyclohexane, a hydrocarbon solvent), P (1-pentanol, an alcohol solvent), and T (toluene, an aromatic hydrocarbon solvent). These represent common industrial chemical families. For tasks involving chemicals outside these tested types, a COSHH assessment under the Control of Substances Hazardous to Health Regulations 2002 should be conducted to confirm whether this gauntlet provides sufficient protection for the specific substances in use.
Q: Why does this gauntlet carry CAT III classification and what does that mean in practice?
A: PPE is classified under UK PPE Regulations into three categories based on the severity of the risk being protected against. CAT I covers minimal risks. CAT II covers intermediate risks. CAT III covers serious or mortal risks, including chemical exposure, high cut hazards, and situations where the consequence of PPE failure could be death or irreversible injury. CAT III products require independent third-party assessment and certification before CE marking, as opposed to CAT II products which can be self-certified by the manufacturer for some aspects. In practice, CAT III on a procurement specification means the gauntlet has passed the most stringent compliance pathway available under UK PPE Regulations.
Q: Is the EN388 puncture resistance rating the same as needle-stick protection?
A: No. The EN388 puncture test uses a blunt 1mm-diameter probe pressed through the glove material at a controlled force. Level 4 puncture resistance confirms strong resistance to blunt pointed objects such as nails, wire, and tool tips. It does not assess protection against hypodermic needles or fine-pointed instruments. Operatives in environments where needle-stick risk is present require gloves specifically tested and rated for needle-stick resistance under a separate applicable standard.
Q: How long should a pair last in regular chemical or oily handling use?
A: Service life cannot be specified and depends entirely on the chemical exposure, task intensity, and frequency of use. Nitrile degrades at different rates depending on the specific chemicals contacted, some solvents cause swelling or tackiness after repeated short exposures. Inspect the full coating surface before every shift for swelling, tackiness, discolouration, pinholing, or cracking. Replace immediately when any of these signs are present. Wiping clean after every use and storing away from heat, sunlight, and chemical vapour significantly extends service life.
Q: How quickly can I get these cut resistant gauntlets delivered to an industrial site or depot?
A: Order by 7pm for next-day delivery nationwide at no extra cost on stocked lines. For time-critical requirements, CMT Group offers VIP 2-hour delivery from any CMT depot, UK-wide. Own-fleet vehicles cover over 95% of the UK mainland with live tracking, real-time ETAs, and What3Words integration for precise delivery to any site entrance or compound gate.
Q: What makes CMT Group a reliable source for CAT III certified PPE for high-risk industrial environments?
A: CMT Group holds BSIF Registered Safety Supplier status, ISO 9001:2015 and ISO 14001:2015 accreditations, CHAS Elite approval, and Crown Commercial Service Supplier status, all independently verified. Every product in the CMT range is assessed by the in-house compliance team against current UK PPE Regulations before listing. For procurement teams managing multiple sites or bulk requirements, the EDGE portal provides contract pricing, role-based spending controls, live stock visibility, and full delivery tracking. Rated Excellent on Trustpilot with over 400 verified Reviews.io reviews from UK industrial and construction customers.
