MAX Thermal Fleece Lined Latex Grip Gloves - Cold Weather Construction Handling

MAX Thermal Fleece Lined Latex Grip Gloves

The MAX Thermal Fleece Lined Latex Grip Gloves are built for site operatives who need consistent hand warmth and reliable grip through cold weather construction shifts. The 7-gauge polyester fleece lining provides a noticeably thicker thermal layer than the 10-gauge acrylic liners found in most budget winter grip gloves, retaining heat without the bulk that reduces dexterity on handling tasks. The crinkle latex palm delivers a textured grip surface on brick, block, timber, and general construction materials in both dry and lightly damp cold conditions.

Why Choose the MAX Thermal Fleece Lined Latex Grip Gloves

• 7-gauge polyester fleece liner: The thicker 7-gauge construction traps more heat than the 10-gauge acrylic liners standard in this category. Polyester fleece retains warmth even when slightly damp, where acrylic liners lose thermal performance. For operatives working through a full cold-weather shift, the liner choice directly affects how long they can keep the gloves on.

• Crinkle latex palm grip: The textured crinkle surface creates multiple contact points on rough construction materials, maintaining traction on brick, block, and timber in cold, dry, and lightly damp conditions. Flat latex coatings lose grip performance faster in cold temperatures.

• High dexterity for precision tasks: Despite the thermal lining, the 7-gauge construction and palm-only coating allow for finger sensitivity and dexterity on tasks requiring controlled handling, tool use, and material placement.

• Hi-vis yellow body: The high-visibility yellow liner is visible at distance on site without additional hand PPE, improving operative visibility during material handling, vehicle movements, and low-light winter conditions.

• Breathable open-knit back: The uncoated back of hand allows heat and moisture to escape during sustained handling, preventing the sweating and discomfort that causes operatives to remove gloves mid-task.

• Knitted elasticated cuffs: The cuff seats firmly at the wrist, sealing out cold air and preventing debris ingress during ground-level and trench handling tasks.

• Plastic-free, zero-waste packaging: Part of the CMT ThinkGreen range, supporting sites with ESG and Scope 3 reporting requirements.

What's Included

• 12 pairs of MAX Thermal Fleece Lined Latex Grip Gloves in your chosen size (M, L, XL, or XXL), supplied in plastic-free packaging.

 Specifications

Compatibility

Who Is This For?

The MAX Thermal Fleece Lined Latex Grip Gloves are designed for construction operatives, groundworkers, bricklayers, and general site trades working through cold weather conditions where hand warmth and grip performance both matter. They suit any operative who removes their gloves in cold conditions due to inadequate thermal performance in standard grip gloves. Mechanical and engineering handling teams working in cold outdoor or unheated indoor environments will also find them suitable.

Typical Applications

• General construction site handling in cold and low-temperature conditions

• Bricklaying and block handling during cold weather pours and winter builds

• Site logistics and material unloading in cold or frosty conditions

• Groundwork and drainage tasks in cold ambient temperatures

• Mechanical and engineering assembly in cold or unheated workshop environments

• Scaffold handling and general site labouring during cold weather months

• Cold store and chilled environment handling where light grip and warmth are required

How to Use

1. Select the correct size: M (8), L (9), XL (10), or XXL (11). A correct fit keeps the fleece liner close to the hand and maximises thermal performance.

2. Pull the glove fully over the hand and seat the elasticated cuff firmly at the wrist to seal out cold air.

3. Check there are no gaps at the cuff before starting work. Cold air entering at the wrist reduces thermal performance significantly.

4. Inspect the latex palm coating before each use. Replace when cracking, peeling, or thinning is visible at the fingertips or palm.

5. Do not use for tasks requiring full waterproof protection or cut resistance above EN388 level 2.

Safety

Certified to EN388:2016+A1:2018 (2242X) for mechanical risk protection. The crinkle latex palm provides grip in cold, dry, and lightly damp conditions but these gloves are not waterproof. For tasks involving wet concrete, cement slurry, or sustained water contact in cold weather, use the MAX Thermal Foam Latex Waterproof Gloves instead. Not suitable for chemical contact, heat, or flame. Operatives with a latex allergy must not use these gloves.

Maintenance

Rinse in clean water after use if contaminated and air dry away from direct heat. Heat degrades both the latex coating and the polyester fleece lining. Store away from solvents and direct sunlight. Inspect the palm coating before each shift and replace when wear is visible at the fingertips or palm centre.

Frequently Asked Questions

Q: What makes the fleece lining on these gloves different from standard thermal latex grip gloves?

 A: Most thermal latex grip gloves on the UK market use a 10-gauge acrylic liner. The MAX Thermal Fleece Lined Latex Grip Gloves use a 7-gauge polyester fleece liner. The lower gauge means a thicker construction, and polyester fleece retains warmth more effectively than acrylic, particularly when the liner becomes slightly damp during a shift.

Q: What does the EN388:2016+A1:2018 2242X rating mean?

 A: EN388 is the UK and European standard for mechanical risk glove protection. The 2242X rating breaks down as: abrasion level 2, blade cut level 2, tear level 4, puncture level 2, TDM cut not tested. Tear resistance at level 4 (75N) is notably strong for a thermal grip glove in this category and reflects the durability of the crinkle latex coating over the fleece liner under sustained construction handling.

Q: Are these gloves waterproof?

 A: No. The crinkle latex palm provides grip in lightly damp conditions but the open-knit back absorbs moisture. For cold weather tasks involving wet concrete, rain, or sustained water contact, the MAX Thermal Foam Latex Waterproof Gloves provide both thermal protection and full waterproof coverage.

Q: What is the difference between these and the MAX Thermal Foam Latex Waterproof Gloves?

 A: The MAX Thermal Foam Latex Waterproof Gloves are double-dipped and fully coated, providing waterproof protection for concrete handling and groundwork in wet cold conditions. The MAX Thermal Fleece Lined Latex Grip Gloves are palm-coated only, providing greater dexterity and breathability for dry or lightly damp cold weather handling tasks where waterproofing is not required.

Q: Why does the hi-vis yellow body matter on a construction site?

 A: The high-visibility yellow liner remains visible at distance during material handling, site logistics, and vehicle movements. In low-light winter conditions and on busy sites, hand visibility contributes to operative safety without requiring additional PPE.

Q: Are these suitable for precision handling tasks?

 A: Yes. Despite the 7-gauge fleece liner, the palm-only coating and crinkle latex texture maintain good fingertip sensitivity and dexterity for controlled handling, tool use, and material placement in cold conditions.

Q: Can operatives with a latex allergy use these?

A: No. These gloves contain natural latex. Operatives with a confirmed or suspected latex allergy must not use them and should be issued a nitrile-coated alternative.

Q: Are these part of the CMT ThinkGreen range?

 A: Yes. Supplied in plastic-free, zero-waste packaging as part of CMT ThinkGreen, supporting sites with ESG and Scope 3 reporting requirements.

Q: How do I order and what are the delivery options?

 A: Order at cmt.co.uk. Next working day delivery for online orders placed by 7pm. VIP dedicated delivery is available UK-wide, dispatched within 30 minutes on a dedicated vehicle. Trade accounts and bulk pricing are managed through the EDGE procurement portal with agreed pricing, role-based spending controls, and live delivery tracking.