NLG Nips Tool Tethering Kit is a 3kg-rated tethering system built specifically for steelfixer's nips, using a swivel attachment that stops the lanyard tangling as the tool rotates.
- 360 D-Ring Locking Loop swivels freely with the nips
- Extended Coil Lanyard keeps slack managed during rebar tying
- Tool Holster keeps nips accessible when not in active use
- Tether Tape fits the attachment to the nips handle
- Rated to 3kg (6.6lbs)
NLG Nips Tool Tethering Kit - Swivel Attachment for Steelfixers
NLG Nips Tool Tethering Kit is a 3kg-rated tethering system built specifically for steelfixer's nips, using a swivel attachment that stops the lanyard tangling as the tool rotates.
- 360 D-Ring Locking Loop swivels freely with the nips
- Extended Coil Lanyard keeps slack managed during rebar tying
- Tool Holster keeps nips accessible when not in active use
- Tether Tape fits the attachment to the nips handle
- Rated to 3kg (6.6lbs)
Order 1x to earn 108 FASTPoints
Order to earn 108 FASTPoints
Log in to access trade discountsNLG Nips Tool Tethering Kit
NLG Nips Tool Tethering Kit solves a specific mechanical problem: steelfixer's nips rotate continuously in the hand during the twist-and-cut motion of tying rebar, and a fixed tether point winds the lanyard up and tangles it within minutes of use. This kit uses a 360 D-Ring Locking Loop that swivels freely as the nips rotate, paired with an Extended Coil Lanyard, Tether Tape to fit the attachment, and a Tool Holster for when the nips are set down between ties. Rated to 3kg, the complete system is built specifically around the working motion of this one tool.
Why nips need a swivel attachment, not a fixed D-ring
Steelfixer's nips are used in a continuous twisting motion to tie rebar wire, meaning the tool rotates fully in the hand many times during a single tie. A fixed tether ring or D-ring attached to the handle winds the lanyard tighter with every rotation, until it either snags, shortens to an unusable length, or places strain on the attachment point itself. The 360 D-Ring Locking Loop in this kit swivels independently of the tool's rotation, so the lanyard stays untangled and at a consistent working length no matter how many times the nips are turned during a tie.
Key Features
-
360 D-Ring Locking Loop: swivels freely as the nips rotate, preventing lanyard tangling during the twist-and-cut motion of rebar tying
-
Extended Coil Lanyard: additional reach and coil recovery suited to the repetitive motion of steel fixing work
-
Tether Tape: self-amalgamating wrap that fits the tether point securely to the nips handle
-
Tool Holster: keeps the nips accessible and off the ground when set down between ties
-
Rated to 3kg (6.6lbs): matched to the typical weight of steelfixer's nips and similar end cutters
Who Is This For
Trades and roles:
-
Steelfixers
-
Rebar tying operatives
-
Concrete reinforcement crews
-
Groundworkers using nips or end cutters at height
Industries:
-
Construction
-
Civil engineering
-
Concrete and reinforcement contracting
Specifications
| Specification | Detail |
| Product Name | NLG Nips Tool Tethering Kit - Swivel Attachment for Steelfixers |
| SKU | NLG101559 |
| Product Type | 4-part matched tool tethering kit for nips and end cutters |
| Max Load | 3kg (6.6lbs) |
| Total Products in Kit | 4 different products |
| Total Pieces in Kit | 4 individual pieces (1 of each) |
| NLG ID Technology | Present on eligible individual components |
| Country of Origin | UK |
Kit contents
| NLG 360 D Ring Locking Loop Tool Tether | 1x, Code NLG101495 |
| NLG Tether Tape | 1x, Code NLG101355 |
| NLG Extended Coil Tool Lanyard | 1x, Code NLG101476 |
| NLG Tool Holster | 1x, Code NLG101470 |
Compatibility
| Application or condition | Status |
| Steelfixer's nips and similar rotating end cutters | Compatible |
| Tools requiring continuous rotation during use | Compatible |
| Belt-mounted storage between ties via the Tool Holster | Compatible |
| Tools or combined loads exceeding 3kg | Not recommended |
| Use as a personal fall arrest or restraint system | Not recommended |
Who Is This For
The NLG Nips Tool Tethering Kit is used by steelfixers and rebar tying operatives working at height or over exclusion zones where a dropped pair of nips presents a real hazard. It suits any concrete reinforcement crew tethering nips or similar end cutters as part of a formal dropped object prevention programme, particularly on sites where the continuous rotation of the tool during tying has made standard fixed tether points impractical in the past.
Typical Applications
-
Tethering steelfixer's nips during rebar tying on elevated structures, formwork, or scaffold.
-
Securing end cutters and similar rotating hand tools where a fixed tether point would tangle during use.
-
Storing nips in the Tool Holster between individual ties, keeping the tool off the working surface without disconnecting the tether.
-
Standardising nips tethering across a steelfixing crew using a single matched kit.
How to Use
Step 1: Wrap the Tether Tape around the nips handle to create a secure base for the attachment point.
Step 2: Fit the 360 D-Ring Locking Loop over the taped section, ensuring the loop can swivel freely.
Step 3: Connect the Extended Coil Lanyard between the D-Ring Locking Loop and a certified anchor point on the belt or harness.
Step 4: Use the Tool Holster to store the nips securely between ties without disconnecting the lanyard.
Step 5: Log inspection of each NLG ID enabled component before first use and at each subsequent formal inspection interval.
Common Mistakes
-
Fitting a fixed tether point instead of the swivel loop: using a standard D-ring rather than the 360 Locking Loop reintroduces the tangling problem this kit is designed to solve.
-
Wrapping the Tether Tape too loosely: a loose base allows the D-Ring Locking Loop to shift or slip during the twisting motion of use.
-
Exceeding the 3kg rating: this kit is rated to 3kg. Confirm the actual weight of the nips or end cutters being tethered is within this limit.
-
Skipping pre-use inspection on individual components: each of the 4 products must be inspected according to its own product datasheet before use.
Safety
This kit is rated to a maximum load of 3kg (6.6lbs). Always confirm the actual weight of the nips or end cutters being tethered is within this rating before use. The 360 D-Ring Locking Loop must be checked before each use to confirm it swivels freely and locks correctly. This kit does not include personal fall arrest, restraint, or work positioning equipment.
Maintenance
Inspect the Tether Tape for wear or loosening, the 360 D-Ring Locking Loop for free swivel movement and correct locking action, the Extended Coil Lanyard's coil recovery and stitching, and the Tool Holster's belt attachment before each use. Clean surface dirt with a water-dampened cloth, using a mild soap or detergent solution for more thorough cleaning. Wipe with a clean cloth and hang to dry away from excessive heat, steam, or sunlight. Complete a formal inspection using the NLG Inspection Checklist at intervals appropriate to frequency of use.
Frequently Asked Questions
Q: Why are steelfixer's nips difficult to tether with a standard D-ring?
A: Nips rotate continuously in the hand during the twist-and-cut motion used to tie rebar wire. A fixed D-ring or tether ring winds the lanyard tighter with every rotation until it snags, shortens to an unusable length, or strains the attachment point. This kit uses a 360 D-Ring Locking Loop instead, which swivels independently of the tool's rotation so the lanyard stays untangled throughout the tying motion.
Q: What exactly is included in the Nips Tool Tethering Kit?
A: The kit includes a 360 D-Ring Locking Loop Tool Tether, Tether Tape to fit the attachment to the nips handle, an Extended Coil Tool Lanyard, and a Tool Holster for storing the nips between ties.
Q: What is the max load rating of this kit?
A: The kit is rated to a maximum of 3kg (6.6lbs), matched to the typical weight of steelfixer's nips and similar end cutters.
Q: What is this kit NOT suitable for?
A: This kit is not suitable for tools or combined loads exceeding 3kg. It does not include personal fall arrest, restraint, or work positioning equipment.
Q: Can this kit be used on tools other than steelfixer's nips?
A: The kit is designed around the rotational working motion of steelfixer's nips and similar end cutters. It suits any tool under 3kg that rotates continuously during use in a similar way, though nips are the primary intended application.
Q: How should the components in this kit be maintained and inspected?
A: Inspect the Tether Tape for wear, the 360 D-Ring Locking Loop for free swivel and correct locking, the Extended Coil Lanyard's coil recovery, and the Tool Holster's belt attachment before each use. Clean with a water-dampened cloth and mild soap solution, then air dry away from heat and sunlight. Complete formal inspections using the NLG Inspection Checklist.
