Rechargeable COB LED work light with four built-in magnets for hands-free steel surface mounting, delivering 800lm at 10W across three selectable brightness levels.
Rechargeable COB LED work light with four built-in magnets for hands-free steel surface mounting, delivering 800lm at 10W across three selectable brightness levels.
Order 1x to earn 48 FASTPoints
Order to earn 48 FASTPoints
Log in to access trade discountsRechargeable COB LED work light with four built-in magnets for instant hands-free positioning on steel surfaces, delivering 800lm at 6500K across three selectable brightness levels. The IP54-rated nylon and TPR housing suits both indoor and outdoor site conditions, and the 30,000-hour LED lifetime removes lamp replacement from the maintenance schedule entirely. Three charging methods are included: USB cable, 13A mains charger, and 12V car adaptor.
A work light that needs a flat surface, a clip point, or a free hand to hold it is a light that competes with the task for the operative's attention. In confined spaces, on steel structures, and in any situation where both hands need to be on the job, a light that requires active positioning becomes the bottleneck. Four strong magnets on the rear of this work light attach directly to steel columns, pipework, vehicle bodywork, and structural members. The light stays where it is placed without any clip, strap, or separate mounting hardware.
4 strong rear magnets: Fix the light to any steel surface instantly, hands-free. The four-magnet configuration holds the unit securely at the angle it is placed without slipping or repositioning during use.
Three brightness modes: 800lm at 100%, 400lm at 50%, and 200lm at 25%. Use 100% for maximum visibility on close tasks, and step down to 50% or 25% to extend battery life across a longer shift.
10W COB LED, 6500K, CRI >80: Daylight-white output across a 120° beam angle. The COB array distributes light evenly across the work area without the hot-spot pattern of a single-lens LED.
USB power bank output: The 5V/1A USB output charges smartphones, tablets, and other USB devices directly from the work light battery while it is in use.
Three charging methods: USB cable, 13A UK mains charger, and 12V car adaptor are all included. Charge from a site office, a vehicle, or any USB power source.
IP54 dust and water spray protection: Rated for dusty indoor environments and outdoor site conditions with water spray exposure.
30,000-hour LED lifetime: No lamp replacement required across the full rated service life.
Class III, CE, RoHS, UKCA: Certified for professional use in UK and European markets.
Trades and roles:
Electricians and M&E engineers
Site maintenance and FM operatives
Vehicle and plant mechanics
Groundworkers and civils operatives
General site operatives on extended shifts
Industries:
Construction and groundworks
Building services and M&E
Vehicle and plant maintenance
Railway maintenance
Industrial and facilities management
| Specification | Detail |
| Product Name | 110V Rechargeable COB LED Work Light – 10W 800lm Magnetic Mount |
| SKU | LED10WRC |
| Lamp Type | COB LED |
| Rated Power | 10W |
| Lumen Output | 800lm (100%), 400lm (50%), 200lm (25%) |
| Colour Temperature | 6500K (daylight white) |
| Colour Rendering Index | >80 |
| Beam Angle | 120° |
| IP Rating | IP54 |
| LED Lifetime | 30,000 hours |
| Magnets | 4 x strong magnets (rear mounted) |
| Battery | Li-ion 3.7V / 4400mAh (built-in) |
| Running Time | Approx. 3 hours |
| Charging Time | 5–6 hours |
| Charging Input | USB, 5V/1A |
| USB Output (power bank) | 5V/1A |
| Safety Level | Class III |
| Certifications | CE, RoHS, UKCA |
| Material | Nylon and TPR |
| Working Temperature | +15°C to +40°C |
| Included Accessories | USB cable, 13A mains charger, 12V car adaptor |
| Dimensions | 172 x 127 x 46mm |
| Application or condition | Status |
| Hands-free magnetic mounting on steel surfaces | ✓ Suitable – 4 strong rear-mounted magnets |
| Indoor and outdoor use within IP54 rating | ✓ Suitable – IP54 dust and water spray protection |
| Three selectable brightness levels for battery management | ✓ Suitable – 100%, 50%, 25% output modes |
| Charging devices via USB power bank output | ✓ Suitable – 5V/1A USB output |
| Charging from mains, car, or USB source | ✓ Suitable – all three chargers included |
| Ambient temperatures between +15°C and +40°C | ✓ Suitable – within rated working temperature range |
| Use in ambient temperatures below +15°C | ✗ Not recommended – minimum working temperature is +15°C; performance may be affected in cold UK winter conditions |
| Water immersion or sustained heavy rain | ✗ Not suitable – IP54 covers dust and water spray, not immersion |
| Battery replacement at end of life | ✗ Not possible – battery is built-in and non-removable |
Electricians, maintenance engineers, and site operatives who need a portable, hands-free work light that attaches directly to the steel structures they are working on. The four-magnet mount eliminates the need for a flat floor surface or a separate clip, making this suitable for confined spaces, inside plant, on vehicle bodywork, and in any position where a freestanding or clip-mounted light is impractical.
Attaching to steel pipework, structural members, or cable tray during electrical and M&E installation work.
Mounting on vehicle bodywork or machinery during workshop and on-site maintenance.
Close inspection work in plant rooms, ducts, and confined spaces where both hands need to be free.
Site compound and welfare area lighting during early starts and late finishes in warmer months.
Railway maintenance and inspection tasks where compact, battery-powered hands-free lighting is needed.
Charging a mobile phone or tablet from the USB output during extended deployments without a separate power bank.
Step 1: Confirm the battery is charged. Press the power button to switch on. The light starts at 100% brightness by default.
Step 2: Press the power button again to step down to 50% brightness, and again for 25%. A further press switches the unit off.
Step 3: To mount magnetically, press the rear of the unit firmly against any clean steel surface. The four magnets hold the unit in position without additional support.
Step 4: Adjust the angle by tilting the unit against the magnetic surface before pressing firmly into position.
Step 5: To recharge, connect the USB cable to the charging port and plug into a power source using the 13A mains charger, 12V car adaptor, or any 5V USB source. Full charge takes 5 to 6 hours.
Step 6: To charge a device, plug a USB cable into the USB output port. Charging runs simultaneously with the light.
Using in ambient temperatures below 15°C: the minimum working temperature for this unit is 15°C. Deploying in cold UK winter conditions below this threshold may affect battery performance and light output. For cold weather outdoor use, a mains-connected alternative is more reliable.
Leaving the battery fully depleted for extended periods: recharge before storing. A fully discharged Li-ion battery stored for long periods degrades in capacity.
Mounting on painted, corroded, or plastic-coated surfaces: the magnets work on ferrous steel. Heavy paint layers, rust treatment coatings, and non-metallic surfaces reduce holding strength. Test the hold before trusting the mount in an overhead or angled position.
Minimum working temperature is 15°C. Do not use in ambient temperatures below this, particularly in cold outdoor winter conditions. The battery is built-in and non-removable. Do not attempt to open or modify the unit. Use only the supplied chargers or a compatible 5V/1A USB source. Do not expose to sustained water or immersion. Check the magnetic hold before trusting the unit in a position where dropping it could cause injury or damage.
Wipe the housing with a dry or lightly damp cloth. Do not use solvents. Keep the USB ports free from dust and debris. Recharge every three months if the unit is stored unused for extended periods. The 30,000-hour LED lifetime means the light source requires no routine maintenance.
Q: How do the four magnets work and what surfaces do they stick to?
A: Four strong magnets are built into the rear of the unit. Press the rear of the light against any clean ferrous steel surface and it holds in position without clips, ties, or additional hardware. Suitable surfaces include structural steelwork, pipework, cable tray, machinery, and vehicle bodywork. On heavily painted, corroded, or plastic-coated surfaces, holding strength is reduced. Test the hold before trusting the mount in an overhead or angled position.
Q: What are the three brightness levels and how does each affect battery life?
A: The three selectable modes cycle with each press of the power button: 800lm at 100%, 400lm at 50%, and 200lm at 25%. The 3-hour rated runtime is based on the 100% setting. Running at 50% approximately doubles runtime; running at 25% extends it further still. For longer shifts or lower-priority background illumination, stepping down from 100% is the most effective way to manage battery life.
Q: What is this NOT suitable for?
A: The minimum working temperature is 15°C. Do not use in cold outdoor conditions where ambient temperature drops below this, as battery performance and light output may be affected. The battery is non-removable. IP54 covers dust and water spray but not immersion or sustained heavy rain. Non-steel or heavily coated surfaces reduce magnetic holding strength.
Q: Can I charge my phone or tablet from this work light?
A: Yes. The USB output on the unit provides 5V/1A, which is sufficient to charge a smartphone. Connect a USB cable between the work light's USB output and the device while the light is in use. The USB output and the light operate simultaneously from the same battery, so running both at once will reduce total battery runtime.
Q: What charging options are included and how long does charging take?
A: Three charging accessories are included: a USB cable, a 13A UK mains plug USB charger, and a 12V car adaptor. Any of these can be used to charge the unit via the USB charging input. A full charge from empty takes approximately 5 to 6 hours. The 13A mains charger is the fastest option under normal conditions.
Q: Is this suitable for cold weather outdoor construction sites?
A: The rated minimum working temperature is 15°C. In UK winter conditions, particularly on exposed outdoor sites where ambient temperatures drop below this, the battery may not deliver its full rated runtime and light output may be reduced. For reliable cold weather outdoor lighting, a mains-connected alternative such as the 110V LED Globe Site Light or a 110V site bulkhead is a more dependable choice.
