IP67-rated hard carry case for two Dustlight personal dust monitors, with custom foam interior and charging cables included for storage and transport between sites.
IP67-rated hard carry case for two Dustlight personal dust monitors, with custom foam interior and charging cables included for storage and transport between sites.
| BULK DISCOUNT | 10 | 30 |
|---|---|---|
| Price | £199.00 £238.80 | £189.00 £226.80 |
Order 1x to earn 209 FASTPoints
Order to earn 209 FASTPoints
Log in to access trade discountsIP67-rated hard carry case for two Dustlight personal dust monitors, with a custom foam interior fitted to hold two units securely during transport. Two USB-to-magnetic charging cables are included. The power supply unit and USB distributor are sold separately.
IP67 means the case is completely dustproof and withstands immersion in up to 1 metre of water for 30 minutes. It protects the Dustlight units from the conditions they are used to monitor.
Monitoring equipment carried between sites, stored in vehicle boots, or left in welfare units between shifts is exposed to the same dust and wet weather conditions it is designed to measure. A basic carry bag provides no meaningful protection against either. An IP67-rated polypropylene case keeps both out. The custom foam interior holds each Dustlight unit in a fixed position so it does not move during transport, and the convoluted lid foam absorbs impact from above when the case is stacked or dropped.
IP67 protection: Completely dustproof and waterproof to 1m depth for 30 minutes. Suited to outdoor site conditions, rain, and transit in open vehicles without additional weatherproofing.
Custom foam interior: The base foam is precision-cut for two Dustlight units. Each unit sits in its own slot without movement during transport. A separate foam section holds the charging cables.
2x charging cables included: Both USB-to-magnetic cables are supplied. Charging requires a power supply unit and USB distributor, sold separately.
Hard polypropylene body: Impact-resistant shell protects the units from knocks during loading, transit, and stacking.
Convoluted lid foam: Egg-crate foam on the lid underside cushions the top of the units when the case is closed.
Snap fasteners: Secure the case closed during transit. Padlock-compatible for added security.
Trades and roles:
Site managers
Health and safety officers
Construction companies managing shared Dustlight units
Facilities managers running multi-shift monitoring programmes
Industries:
Construction
Civil engineering
Woodworking and joinery
Metalworking and fabrication
Manufacturing
| Specification | Detail |
| Product Name | IP67 Hard Case for Dustlight - 2 Unit Capacity with Charging Cables |
| SKU | ME100005 |
| IP Rating | IP67 (completely dustproof; waterproof to 1m depth for 30 minutes) |
| Capacity | 2 Dustlight units |
| Interior | Custom-cut foam with dedicated slots for 2 Dustlight units and cable storage |
| Included | 2x USB-to-magnetic charging cables |
| Not Included | Power supply unit and USB distributor (sold separately) |
| Case Material | Hard polypropylene |
| Lid Interior | Convoluted foam |
| Colour | Black |
| Application or condition | Status |
| Dustlight personal dust monitors (2 units) | ✓ Compatible |
| Site vehicle transport and on-vehicle storage | ✓ Suitable |
| Outdoor storage in rain and wet conditions | ✓ Suitable (IP67 rated) |
| Dusty site environments | ✓ Suitable (completely dustproof) |
| Welfare unit and site office storage between shifts | ✓ Suitable |
| Charging inside the closed case | ✗ Not suitable. Open case for charging. |
| Storage of more than 2 Dustlight units | ✗ 2-unit capacity only |
| Sustained submersion beyond 1m depth or 30 minutes | ✗ Outside IP67 rating |
The case is used by site managers and health and safety officers who move Dustlight units between sites, store them in vehicles, or manage shared units across multiple shifts. It protects the investment in monitoring equipment between uses and keeps charging cables organised alongside the devices. It suits any operation where two Dustlight units are in active circulation and need a reliable, weatherproof home between deployments.
Transporting two Dustlight units between construction sites in a company vehicle, keeping the monitors protected from dust and rain in the boot or cab.
Storing two units in a welfare unit between shifts, with charging cables to hand for overnight charging before the next deployment.
Carrying two units to site as part of a health and safety inspection or monitoring programme, where the case doubles as the transport container and the storage solution at the end of the visit.
Protecting units during storage in dusty or outdoor locations such as site compounds, plant stores, or outbuildings where unprotected equipment would accumulate contamination.
Step 1: Open the snap fasteners and lift the lid.
Step 2: Place each Dustlight unit face-up in its designated foam slot in the base. Each slot is cut to fit one unit. Do not force a unit with an attached armband or connector into a slot not shaped for it.
Step 3: Coil the charging cables and place them in the dedicated cable section of the foam insert.
Step 4: Close the lid and fasten the snap closures before moving the case.
Step 5: To charge, open the case and connect each charging cable to the device and to a powered USB port. The case is not designed for charging with the lid closed.
Step 6: If storing in an outdoor location, keep the case on a raised surface where possible to avoid prolonged contact with standing water beyond the IP67 rating parameters.
Storing units with accessories attached: Klick Fast armbands and Go Connectors attached to the Dustlight units may not fit within the custom foam slots. Remove accessories before placing units in the case.
Assuming the case charges the units: The case includes charging cables but not a power source. A USB power supply and distributor are required and sold separately. The case is a storage and transport solution, not a charging dock.
Closing the case during charging: The case is sealed when closed. Do not charge units with the lid fastened as heat may build up. Always charge with the case open.
Leaving the case sealed in direct sunlight for extended periods: IP67 cases can retain heat. Store out of direct sunlight in hot weather, particularly when units are inside.
The case protects equipment only. It does not make the Dustlight units inside it suitable for any application they are not already rated for. The IP67 rating covers dust ingress and water immersion to 1m for 30 minutes. Do not submerge beyond these parameters. Do not charge units inside a closed, sealed case.
Wipe the exterior with a damp cloth. Clear debris from the seal and closure mechanism after use in muddy or gritty conditions, as debris on the seal can prevent a full IP67-compliant closure. Inspect the foam insert periodically for compression damage or contamination. Replace foam if it no longer holds units securely in position.
Q: What does IP67 mean for this case?
A: IP67 is an ingress protection rating covering two hazards. The 6 means the case is completely dustproof, with no dust able to enter the enclosure. The 7 means it can be submerged in up to 1 metre of water for 30 minutes without water ingress. For site use, this means the case protects the Dustlight units from the same dust and wet conditions the monitors are designed to operate in.
Q: Does the case include a power supply for charging?
A: No. The case includes two USB-to-magnetic charging cables, one per Dustlight unit. A power supply unit and USB distributor are required to charge the units and are sold separately. The cables connect the Dustlight units to any compatible power source.
Q: Can I charge the Dustlight units inside the closed case?
A: No. The case should be open when charging. A sealed IP67 case retains heat, and charging with the lid fastened is not recommended. Always open the case before connecting charging cables.
Q: How many Dustlight units does the case hold?
A: Two. The foam insert is precision-cut for exactly two Dustlight units. The case is not suitable for storing a third unit or for the Dustlight Workforce 5 Kit, which requires a larger case for full team storage.
Q: Do the Dustlight units need to have their accessories removed before storing?
A: Yes. Klick Fast armbands and Go Connectors attached to the Dustlight units may not fit within the foam slots. Remove any accessories before placing the units in the case for storage or transport.
Q: Can the case be padlocked?
A: The snap fasteners are padlock-compatible, allowing the case to be secured during transport or storage where access control is needed.
Q: What is this case NOT suitable for?
A: It is not suitable for storing more than two Dustlight units. It is not a charging dock and does not power the units inside. It must not be submerged beyond 1 metre depth or for longer than 30 minutes. It is not suitable for use as a protective case for equipment other than Dustlight monitors without confirming internal dimensions against the dimensions of the alternative device.
