Skip to the beginning of the images gallery

NLG bungee tool lanyard flat coiled view showing climbing cord loop and Rotobiner carabiner with NLG ID tag | CMT Group UK

NLG Bungee Tool Lanyard 5kg | CMT Group UK

Green NLG bungee tool lanyard attached to cordless drill showing 360 Rotobiner and tool wrap in use | CMT Group UK

Self-retracting bungee tool lanyard rated to 5kg, for tethering hand tools and power tools at height on UK construction and industrial sites.

Max load 5kg (11lbs), dynamic load tested at 2:1 safety factor
CE and UKCA marked, NS 9611:2022 and ANSI/ISEA 121 compliant
360° Rotobiner, anti-tangle swivel with two-stage locking gate
Self-retracting bungee extends 80cm to 120cm, retracts when slack
Climbing cord loop, cinches to captive handle, hole, or anchor D-ring
Contrast stitching for rapid visual inspection, NLG ID scan tag included

NLG Bungee Tool Lanyard - 5kg Self-Retracting Tool Tethering

Code

NLG101372

3030+ In Stock

Self-retracting bungee tool lanyard rated to 5kg, for tethering hand tools and power tools at height on UK construction and industrial sites.

Max load 5kg (11lbs), dynamic load tested at 2:1 safety factor
CE and UKCA marked, NS 9611:2022 and ANSI/ISEA 121 compliant
360° Rotobiner, anti-tangle swivel with two-stage locking gate
Self-retracting bungee extends 80cm to 120cm, retracts when slack
Climbing cord loop, cinches to captive handle, hole, or anchor D-ring
Contrast stitching for rapid visual inspection, NLG ID scan tag included

£42.54 £35.45

Buy 20 for £40.09 £33.41 each and save 6%
Buy 50 for £37.50 £31.25 each and save 12%

BULK DISCOUNT	20	50
Price	£33.41 £40.09	£31.25 £37.50

Order 1x to earn 35 FASTPoints

Order to earn 35 FASTPoints

3030+ In Stock

Product Details

NLG Bungee Tool Lanyard

Self-retracting bungee tool lanyard rated to 5kg, built for tethering hand tools and power tools when working at height on UK construction, civils, and industrial sites. The bungee webbing retracts to a compact length between uses so there is nothing trailing or snagging on scaffold rails and fittings, and extends smoothly to full reach the moment you need it. At the carabiner end, the 360° swivel rotates freely through a full rotation so a cordless drill or impact driver can turn without winding the lanyard up.

How the Self-Retracting Bungee Solves the Tangle Problem at Height

A fixed-length webbing lanyard stays at one length regardless of what you are doing, it hangs loose when you are stationary, trails when you move, and creates friction when you reach out fully. Over a long shift of overhead work with a power tool, that friction adds physical fatigue and a trailing lanyard that catches on scaffold fittings can snatch a tool from your grip at the wrong moment. The bungee construction retracts to a compact resting length when there is no tension on it and extends smoothly under load, staying out of the way when you are repositioning and giving full reach when you are working.

Key Features

360° Rotobiner swivel carabiner: Rotates freely through a full 360°, preventing the lanyard from twisting or tangling during use. Critical for power tools such as drills and impact drivers that rotate during operation.
Self-retracting bungee webbing: Extends from 80cm to 120cm under load and retracts automatically when slack. Keeps the lanyard clear of the working area without bunching or trailing.
Two-stage locking gate: Requires a deliberate two-step action to open the Rotobiner gate, preventing accidental release during use. Closes and locks automatically on release.
Climbing cord loop: Rugged cord at the anchor end cinches securely around a tool handle, through a captive hole, D-ring, or anchor tether point. Attaches and tightens in seconds with one hand.
Contrast stitching: Colour contrast woven into the bungee webbing allows fast visual inspection of wear and damage without removing the lanyard from the tool or anchor.
CE and UKCA marked: Third-party certified and dynamically load tested at a 2:1 safety factor. Meets UK requirements for dropped object prevention. NLG ID scan tag for digital inspection logging.

Who Is This For

Trades and roles:

Working at height operatives
Scaffolders and steel erectors
Electricians and M and E trades
Site managers specifying dropped object prevention
Safety officers implementing tool tethering programmes

Industries:

Construction
Civil engineering
Utilities
Oil and gas
Rail and infrastructure

Specifications

Specification	Detail
Product Name	NLG Bungee Tool Lanyard - 5kg Self-Retracting Tool Tethering
SKU	101372
Product Category	Tool Lanyard, Dropped Object Prevention
Max Load	5kg (11lbs)
Lanyard Type	Self-retracting bungee
Carabiner	360° Rotobiner, fully anodised aluminium
Gate Mechanism	Two-stage locking, auto-closes on release
Anti-Tangle	Yes, 360° free rotation
Anchor Attachment	Rotobiner clips to D-ring, anchor loop, or tether point
Tool Attachment	Climbing cord loop, choke cinch
Safety Standards	CE, UKCA, NS 9611:2022+AC, ANSI/ISEA 121 (year: confirm before publishing)
Testing	Dynamic load tested, 2:1 safety factor, third-party certified
Inspection System	NLG ID serialised scan tag
Serial Number	Unique serial number per unit
Extended Length	80cm to 120cm
Colour	Hi-vis green
Unit Weight	90g

Compatibility

Application or Condition	Status
Application or condition	Status
Hand tools up to 5kg (11lbs) at height	✓ Compatible
Power tools up to 5kg including cordless drills and impact drivers	✓ Compatible
Tools with captive holes or handles	✓ Compatible
Tools with D-ring anchor points	✓ Compatible
Scaffold, MEWP, elevated platform, and tower use	✓ Compatible
NLG tool bags and rated anchor systems	✓ Compatible
Tools exceeding 5kg (11lbs) including battery and accessories	✗ Not suitable
Fall arrest or personal safety applications	✗ Not suitable
Replacement for EN354 or EN355 personal safety lanyard	✗ Not suitable
Tools with sharp or abrasive edges in direct contact with bungee	✗ Not recommended

Who Is This For

Working at height operatives, scaffolders, steel erectors, electricians, and M and E trades on UK construction and industrial sites who need a reliable power tool lanyard for drills, impact drivers, wrenches, and hand tools. It is equally suited to site safety officers and CDM coordinators specifying a site-wide dropped object prevention programme, and to operatives in oil and gas, utilities, and rail environments where formal tool tethering requirements apply to all work at elevation.

Typical Applications

Tethering a cordless drill or impact driver to a harness anchor point during overhead fixing and installation work on scaffold or elevated working platforms.
Securing spanners, podgers, and wrenches during steel erection and structural ironwork, where a dropped tool at height presents a direct risk to operatives below.
Using as a power tool lanyard for angle grinders, ratchets, and torque wrenches during elevated fabrication and assembly tasks.
Attaching pliers, cutters, and measuring instruments to a belt or harness D-ring during elevated cable containment installation.
Tethering tools during maintenance and inspection work at height in wind-exposed positions where a momentarily unrestrained tool becomes an immediate dropped object hazard.
Use as part of a multi-tool tethering setup on sites with formal dropped object prevention requirements written into the CDM 2015 construction phase plan.

How to Use

Rotobiner end, anchor point attachment:

Step 1: Rotate the Rotobiner gate 90 degrees and draw back to open.

Step 2: Clip the open Rotobiner onto the anchor point, harness D-ring, scaffold tube tether, or tool bag loop and release the gate. It closes and locks automatically on release.

Step 3: Confirm the gate is fully closed and locked with a firm tug before beginning work.

Climbing cord end, tool attachment:

Step 4: Pass the climbing cord loop through the tool's captive handle, hole, or anchor D-ring.

Step 5: Pass the Rotobiner end of the lanyard through the cord loop and pull to create a tight cinch. Pull until the loop is firm against the tool.

Step 6: Check both ends are secure with a gentle tug on the lanyard before beginning work.

Note: If a spring-loaded toggle is present on the choke, it is there to prevent the cinch from loosening during use. It is not a secondary lock.

Common Mistakes

Exceeding the 5kg max load: Attach only tools that weigh 5kg or less including any battery or accessory. Weigh the tool with its heaviest attachment before specifying this lanyard.
Attaching to an unrated anchor point: The lanyard is only as secure as its anchor. Clip only to a rated harness D-ring, scaffold anchor, or NLG anchor system, never to an improvised fixing or unrated loop.
Using as fall arrest equipment: This is a tool tether with a 5kg max load rating. It is not a personal safety lanyard and must never be used in any application where a rated fall arrest device is required.
Ignoring the contrast stitching: The contrast stitching is a wear indicator. If the contrast colour is fading or absent at any point along the bungee, the webbing at that point has degraded and the lanyard must be retired from service.
Continuing to use after a drop event: After any drop, quarantine the lanyard for a thorough inspection before returning to service. Dynamic loading during a fall can cause internal damage that is not visible externally.

Safety

This lanyard is rated to a maximum working load of 5kg (11lbs). It is not fall arrest equipment and must not be used in any application where a rated personal safety lanyard is required under the Work at Height Regulations 2005. Always match the lanyard rating to the confirmed weight of the tool before use. Inspect before every shift. Quarantine after any drop event. The climbing cord cinch must be re-checked at the tool before beginning work, a loose cinch that comes undone during use defeats the purpose of the tether entirely.

Maintenance

Inspect the bungee webbing, climbing cord, Rotobiner body, and gate mechanism before every use. Check the contrast stitching for signs of wear or colour loss along the full length of the bungee. Check the Rotobiner gate opens, rotates, and closes cleanly. Remove from service immediately if any component is worn, deformed, or damaged. Store away from direct sunlight, heat sources, and chemical contact. Log all inspections via the NLG ID scan tag to maintain a digital inspection record. Detailed inspection checklists are accessible by scanning the tag on the lanyard.

Frequently Asked Questions

Q: How do I know if this tool lanyard is rated for my power tool?
A: Weigh the tool fully assembled, including the battery and any accessory fitted during use. If the total weight is 5kg (11lbs) or under, this lanyard is rated for the application. For tools exceeding 5kg, you need a higher-rated lanyard. The 5kg limit is the maximum working load, not an average, it applies to the tool at its heaviest configuration.

Q: What does dynamic load tested at 2:1 safety factor mean?
A: Dynamic testing applies a sudden shock load to simulate a tool falling and the lanyard arresting it, rather than simply applying a static weight. A 2:1 safety factor means the lanyard is tested to twice its rated working load, in this case, 10kg of dynamic force, before certification is granted. Third-party certification means an independent laboratory conducted those tests, not the manufacturer. This is the certification basis that makes the CE and UKCA markings valid on UK sites.

Q: What is this lanyard not suitable for?
A: This is a tool tether with a 5kg working load limit, it must not be used to tether tools heavier than 5kg (11lbs) including battery and accessories. It is not a fall arrest device and must never be used in any personal safety application. It does not replace a rated EN354 or EN355 safety lanyard or harness. Do not use where the bungee is in direct contact with sharp or abrasive tool edges that could cut the webbing during use.

Q: Why does the 360° swivel matter for power tools specifically?
A: A cordless drill, impact driver, or socket wrench rotates during operation. Without a swivel at the carabiner end, each rotation winds the lanyard tighter until it either restricts tool movement or creates enough tension to drag the tool. The 360° Rotobiner swivel turns with the tool, absorbing that rotation so the bungee stays slack, the operator retains full tool control, and the lanyard stays clear throughout the task. For hand tools that do not rotate, the swivel still prevents tangles when the operator moves and changes position.

Q: How do I attach this to a tool with no captive hole or dedicated tether point?
A: Use an NLG tool wrap or tether tape to create a fixed attachment point on the tool body. Tool wraps are hook-and-loop straps that wrap around drill bodies, handles, and grips, with a D-ring attachment point for the climbing cord to cinch onto. This method works on any tool regardless of whether it has a factory-fitted captive hole or anchor point. CMT stocks NLG tool wraps alongside this lanyard.

Q: How do I inspect this lanyard before use?
A: Run your hand along the full length of the bungee and check for fraying, thinning, or areas where the contrast stitching has faded, faded contrast indicates webbing wear at that point. Check the climbing cord for cuts, fraying, and looseness at the sewn termination. Check the Rotobiner body for deformation, the gate for clean rotation and positive locking, and confirm it opens only with a deliberate two-stage action. If anything fails the check, retire from service. Log the inspection via the NLG ID scan tag.

Q: Which safety standards does this meet for UK construction sites?
A: The lanyard carries CE and UKCA marking and meets NS 9611:2022+AC and ANSI/ISEA 121 compliance standards. It is dynamically load tested and third-party certified at a 2:1 safety factor — the standard required for dropped object prevention equipment under the Work at Height Regulations 2005. Each unit carries a unique serial number and NLG ID scan tag, enabling digital inspection logging to support the audit trail required under CDM 2015 construction phase plans.

Knowledge Centre