Short coil tool lanyard rated to 3kg with dual 360° Quick Clip connectors that open and close with one thumb bar action, fully operable with construction gloves.
- Max load 3kg (6.6lbs), dynamic load tested at 2:1 safety factor
- CE and UKCA marked, NS 9611:2022 compliant
- serial numbered
- Dual 360° Quick Clips, single thumb bar action, auto-closes on release
- Extends 4cm to 70cm
- lightweight PU core
- Anti-puncture wipe-clean sleeve for dirty environments
- Pairs with NLG GO Wrist Lanyard
- NLG ID scan tag included
NLG Short Coil Tool Lanyard Quick Clip - 3kg Glove Operable Tool Tethering
Short coil tool lanyard rated to 3kg with dual 360° Quick Clip connectors that open and close with one thumb bar action, fully operable with construction gloves.
- Max load 3kg (6.6lbs), dynamic load tested at 2:1 safety factor
- CE and UKCA marked, NS 9611:2022 compliant
- serial numbered
- Dual 360° Quick Clips, single thumb bar action, auto-closes on release
- Extends 4cm to 70cm
- lightweight PU core
- Anti-puncture wipe-clean sleeve for dirty environments
- Pairs with NLG GO Wrist Lanyard
- NLG ID scan tag included
- Buy 10 for £22.44 £18.70 each and save 6%
- Buy 20 for £20.28 £16.90 each and save 15%
| BULK DISCOUNT | 10 | 20 |
|---|---|---|
| Price | £18.70 £22.44 | £16.90 £20.28 |
Order 1x to earn 19 FASTPoints
Order to earn 19 FASTPoints
Log in to access trade discountsNLG Short Coil Tool Lanyard Quick Clip
Short coil tool lanyard rated to 3kg, with dual 360° Quick Clip connectors that open and lock with a single thumb bar pull and release — no screwing, no collar tightening, operable with full construction gloves throughout. The compact coil extends from 4cm to 70cm and is designed to pair with the NLG GO Wrist Lanyard for a wrist-anchored tethering setup, or to connect from a belt D-ring or harness anchor in confined spaces. The 360° swivel at each end prevents the coil from building up rotational tension when the tool rotates during use.
How the Quick Clip Solves the Gloves Problem
A standard screw gate carabiner requires the operative to tighten the locking collar after every clip, which in practice means removing a glove or rolling it back in cold or wet conditions. Operatives working through a full shift choose between cold hands and an unlocked gate, either outcome is a safety problem. The Quick Clip opens with a pull of the thumb bar and locks automatically when the bar is released, without a collar to tighten or a screw to wind. The clip opens and closes in one motion with thick construction gloves still on, making it practical enough that operatives actually use it every time rather than leaving the lanyard unclipped between tasks.
Key Features
-
Dual 360° Quick Clip connectors: Single thumb bar action opens the gate and auto-close locks it on release. Full 360° swivel prevents coil tension when rotating hand tools are in use. Operates with construction gloves on without any adjustment.
-
Ultra-compact short coil: Extends from 4cm to 70cm. Retracts to a compact loop that stays clear of the working area and reduces snagging hazards in confined spaces and restricted access positions.
-
Lightweight PU core: Durable and light construction for all-day wear when paired with a wristband or clipped to a belt D-ring across extended site shifts.
-
Anti-puncture wipe-clean sleeve: The outer sleeve resists puncture from tool contact, rough surfaces, and site debris, and wipes clean easily. Suited to dirty, oily, and harsh working environments where a standard cord would degrade quickly.
-
CE and UKCA marked, serial numbered: Certified and dynamically load tested at a 2:1 safety factor. NLG ID scan tag and unique serial number for inspection traceability.
Who Is This For
Trades and roles:
-
Site operatives working with hand tools up to 3kg who wear construction gloves throughout the shift
-
Electricians and M and E maintenance engineers in standard (non-live) environments
-
Confined space workers needing a compact wrist-mounted tethering solution
-
Safety officers specifying glove-operable team-issue wristband tethering kits
Industries:
-
Construction and building maintenance
-
Civil engineering
-
Electrical and M and E
-
Utilities and industrial maintenance
Specifications
| Specification | Detail |
|---|---|
| Product Name | NLG Short Coil Tool Lanyard Quick Clip - 3kg Glove Operable Tool Tethering |
| SKU | 101364 |
| Product Category | Quick Clip Coil Tool Lanyard, Dropped Object Prevention |
| Max Load | 3kg (6.6lbs) |
| Lanyard Type | Short coil |
| Connector Type | Dual 360° Quick Clip, single thumb bar action |
| Gate Mechanism | Pull thumb bar to open, auto-closes and locks on release |
| Glove Operation | Yes, fully operable with construction gloves |
| Anti-Tangle | Yes, 360° swivel eradicates coil tension during tool rotation |
| Core Material | Lightweight PU |
| Sleeve | Anti-puncture wipe-clean outer sleeve |
| Safety Standards | CE, UKCA, NS 9611:2022+AC |
| Testing | Dynamic load tested, 2:1 safety factor, third-party certified |
| Inspection System | NLG ID serialised scan tag |
| Serial Numbering | Unique serial number per unit |
| Extended Length | 4cm to 70cm |
| Colour | Hi-vis green |
| Unit Weight | 90g |
Compatibility
| Application or Condition | Status |
|---|---|
| Hand tools up to 3kg at height | ✓ Compatible |
| Screwdrivers, pliers, and small rotating hand tools | ✓ Compatible |
| Wristband anchor configuration with NLG GO Wrist Lanyard (101599) | ✓ Compatible |
| Belt D-ring and harness anchor configuration | ✓ Compatible |
| Confined spaces and restricted access positions | ✓ Compatible |
| Dirty, oily, and harsh site environments | ✓ Compatible |
| Electrical or non-conductive required environments | ✗ Not suitable, use 101376 |
| Tools exceeding 3kg (6.6lbs) | ✗ Not suitable |
| Fall arrest or personal safety applications | ✗ Not suitable |
| Replacement for EN354 or EN355 personal safety lanyard | ✗ Not suitable |
Who Is This For
Site operatives, electricians, M and E maintenance engineers, and confined space workers who use hand tools up to 3kg throughout the shift and need a tool tethering solution that can be attached and detached without removing construction gloves. It is equally suited to safety officers and procurement managers specifying a team-issue wristband tethering kit where operatives need to clip tools in and out repeatedly across a working day without breaking glove hygiene or creating a stop-start workflow.
Typical Applications
-
Tethering a screwdriver to a wristband anchor during elevated fixing and installation work, where the 360° swivel allows the screwdriver to rotate freely without winding the coil.
-
Keeping pliers, cutters, and small hand tools secured during overhead M and E installation work in confined riser shafts and plant rooms where a longer lanyard would trail.
-
Clipping to a belt D-ring for hand tool tethering during scaffold and structural work where a wristband is not appropriate but the operative wears full construction gloves.
-
Use as part of a team-issue wristband tethering programme on construction sites where all operatives carry hand tools at height and the Quick Clip's glove-operable action removes the practical barrier to consistent use.
-
Pairing with the NLG GO Wrist Lanyard (101599) to create a complete wrist-anchored tethering system for small hand tools in confined spaces, access voids, and restricted working positions.
-
Tethering tools in dirty and oily environments such as plant rooms and mechanical service areas where the anti-puncture wipe-clean sleeve handles regular contact with grease and site debris.
How to Use
Step 1: Rotate the Quick Clip 90 degrees to align the swivel for connection.
Step 2: Pull the thumb bar down to open the clip gate.
Step 3: Place the open clip onto the anchor point, D-ring, wristband loop, or tool attachment point and release the thumb bar. The gate closes and locks automatically.
Step 4: Check both ends are securely fastened with a gentle tug on the lanyard before beginning work. Both Quick Clips should be closed and immovable under a firm tug.
Note: Repeat the same process at the tool end. Both ends use identical Quick Clip connectors operated by the same thumb bar mechanism.
Common Mistakes
-
Not checking auto-close after release: The Quick Clip locks automatically but confirm both clips are fully closed with a tug before starting work. In dirty environments, debris in the gate area can occasionally prevent a full close.
-
Exceeding the 3kg max load: Weigh the tool before attaching. A heavy box spanner or large ratchet may approach or exceed 3kg. For tools above 3kg, use the NLG 5kg or heavier bungee lanyard.
-
Using in electrical environments: The Quick Clips are metal construction and are not suitable for live working environments where metal-free tethering is required. Use the non-conductive short coil lanyard (101376) for electrical applications.
-
Leaving the coil dirty after work in oily environments: Grease, cement, and cutting fluids left on the sleeve harden and degrade the PU coating over time. Wipe after every shift in harsh environments.
-
Continuing after a drop event: Quarantine and inspect after any drop before returning to service.
Safety
This lanyard is rated to a maximum working load of 3kg (6.6lbs). It is not for fall arrest and must not be used in any personal safety application. The metal Quick Clip connectors are not suitable for electrical work environments or sites requiring non-conductive or metal-free equipment, use the NLG Short Coil Tool Lanyard Non Conductive (101376) for those applications. Inspect both Quick Clips, the coil, and the sleeve before every use. Retire from service if any component is cracked, deformed, or damaged. Quarantine after any drop event.
Maintenance
Wipe the anti-puncture sleeve clean with a damp cloth after every use in dirty or oily environments. Inspect both Quick Clip connectors for deformation and confirm the thumb bar opens the gate cleanly and the gate closes fully on release. Check the coil body for kinking or surface damage along its full length. Inspect the connection between the coil and both clip ends. Store away from direct sunlight and chemical solvents. Log inspections via the NLG ID scan tag. Retire from service when any component shows deterioration or after any drop event.
Frequently Asked Questions
Q: How does the Quick Clip work and why is it better for gloved operatives?
A: The Quick Clip opens with a single pull of the thumb bar on the side of the connector and locks automatically when the bar is released, no collar to tighten, no screw to wind. For an operative wearing thick construction or work gloves, this means attaching and detaching a tool takes one motion with no need to remove or roll back a glove. Standard screw gate carabiners require a collar to be tightened after clipping, which realistically means either skipping the tightening step or removing a glove to do it. The Quick Clip removes that barrier entirely.
Q: What hand tools is this suitable for?
A: Any hand tool weighing 3kg or less with a D-ring, captive hole, or attachment loop that either Quick Clip can connect to. Screwdrivers, pliers, cutters, small wrenches, and socket drivers are all within the load limit and typically have the attachment points the clip needs. The 360° swivel specifically suits rotating tools like screwdrivers, where the clip turns with the tool rather than winding the coil.
Q: What is this NOT suitable for?
A: Tools exceeding 3kg (6.6lbs). Electrical or live working environments, the Quick Clips are metal and this is not a non-conductive product. Fall arrest or any personal safety application. For metal-free environments, use the non-conductive short coil lanyard (101376). For tools over 3kg, use the NLG 5kg bungee lanyard (101372) or heavier.
Q: How does the dual spin design prevent coil tension?
A: When a rotating tool such as a screwdriver is used, every rotation puts a small amount of twist into a fixed-connection lanyard. Over repeated uses across a shift, this builds up as tension in the coil. The 360° swivel at each Quick Clip absorbs that rotational movement before it reaches the coil body, so the coil stays in its natural extended state rather than tightening around its own axis. The result is consistent, low-resistance reach throughout the shift.
Q: How does this pair with the NLG GO Wrist Lanyard?
A: The Quick Clip at one end connects to the loop on the NLG GO Wrist Lanyard (101599), worn on the wrist. The Quick Clip at the other end connects to the tool D-ring or attachment point. This creates a wrist-anchored, hands-free tethering system that stays compact enough for confined spaces and restricted access positions, with the Quick Clip allowing the tool to be detached and reattached in one hand motion without removing gloves.
Q: Can I use this in dirty or oily environments?
A: Yes. The anti-puncture sleeve is specifically designed to resist the surface contact and debris common in plant maintenance, mechanical service areas, and industrial construction environments. Wipe the sleeve with a damp cloth after use in oily or greasy environments to prevent hardening deposits degrading the coating over time. The PU core handles the physical demands of harsh site use.
Q: How do I inspect this before use?
A: Pull the thumb bar on both Quick Clips and confirm each gate opens cleanly and closes and locks on release. Tug each closed clip firmly to confirm the lock holds. Check the coil body along its full length for kinking and surface damage. Inspect the PU sleeve for cuts or splits. If any component fails the check, retire from service. Log the inspection via the NLG ID scan tag.
